The stepped down circular bar with diameters 2d and d is subjected to a tensile axial force aligned with its axis. The ratio of direct stress in segment AB to direct stress in segments BC is:

Q: A compression load of P = 55 kips is applied to a 3 in. by 3 in. square post, as shown. Determine…

A:

Q: Given force F-800 N and section AB is a bar with a diameter d = 0.05 m. Determine the internal…

A: Given :Force, F=800 NDiameter, d=0.05 mSut= 350 MP aSuc= 550 MP aWe have to identify the bending…

Q: lg (6) Im الله Soan

A:

Q: Segments AB and CD of the assembly are solid circular rods. A) What is the normal stress in segment…

A:

Q: A single-piece bicycle crank is shown below under the following load: the rider pedals forward with…

A:

Q: A homogenous rigid block subjected to the loading shown in figure is supported by three steel rod…

A: Given: Diameter of steel rod, d=25 mm

Q: Construct a Mohr's circle for the following point stresses: o = 60MPa, oy = 10MPa and Txy = +20MPa,…

A:

Q: Complete answer

A: Given Data: Diameter of OB and AB (D) = 100 mm = 0.1 m Radius of disc (r) = 0.5 m Allowable normal…

Q: A solid bar has a diameter of 40 mm and subjected to the loadings shown in Figure 2. The supports at…

A:

Q: The assembly consists of two rods AC and BD attached to the 100-lb uniform rigid beam AB. There is a…

A:

Q: The part shown is made from AISI 1040 CD steel and is loaded at point C with 300 N in the positive y…

A: Given : material - AISI 1040 CD diameter of bar d = 12 mmYield strength for AISI 1040 CD is 415 MPa

Q: A bar of diameter 25mm has an axial hole 19mm bored out concentric with the oute circumference. The…

A:

Q: The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column…

A:

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

A:

Q: A motorcycle's clutch hand lever is designed to receive a load from the rider's finger of 50 N at…

A: σ=F​A" data-mce-style="display: inline-block; line-height: 0; text-indent: 0px;…

Q: (3) The cantilever bar as shown on next page is made of a brittle material. At D, F-300 lb, EF-250…

A: Given data :Material of cantilever Bar= Cast iron (Brittle Material)At D: Fx= 300 lb, Fy= 250 lb,…

Q: he bent pipe has a 1.5-in. outer diameter and a 0.2-in. wall thickness. Calculate the largest shear…

A: Let us draw the Free body diagram

Q: Calculate the normal stress in rod BC and the displacement of point D. Also calculate the change in…

A: GivendBC=10cm=0.10mE=50GPaν=0.3P=2.5kN

Q: = A machine component is fabricated from a bent tube as shown below. One part of the tube lies along…

A: Outside diameter, d0=122 mmInside diameter, di=108 mmForce F=8.5 kNLengths,L1=258 mmL2=118 mmL3=281…

Q: (3) The cantilever bar as shown on next page is made of a brittle material. At D, F-300 lb. F-250…

A: Given data :Material of cantilever Bar= Cast iron (Brittle Material)At D: Fx= 300 lb, Fy= 250 lb,…

Q: 2- For the truss structure shown, use symmetry to determine the displacements of the nodes and the…

A:

Q: Figure Q5 shows a thick cylinder of 50 mm internal radius and 130 mm outer radius is subjected to an…

A: 2   Given: The internal radius, ri = 50 mm The outer radius, ro = 130 mm The internal pressure, Pi =…

Q: Find the shear stress about the neutral axis if V = 2000K.

A:

Q: A circular tube is subjected to torque T at itsends. The resulting maximum shear strain in the…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.