Segments AB and CD of the assembly are solid circular rods. A) What is the normal stress in segment CD? 45 KN 20 mm 10 kN 10 KN 20 mm 15 KN 15 KN Find Force at D to answer question Test 2 Do not assist. Do not post. B) If the failure stress of the material is 414 MPa, is the part in danger of failing in segment BC? Why?

Q: Attention !!!! Please clarify this . When they go to calculate both the normal stress of the bolt…

A: Step 1: Step 2: Step 3: Step 4:

Q: Question 1 A bar with a circular cross-section of diameter 12 mm is loaded with an axial force of 10…

A:

Q: Problem 1: If the parts of the shaft below are a 1" diameter solid steel rod and a 2" OD diameter…

A:

Q: The bellcrank is in equilibrium a) determine the diameter of the bar DE if the normal stress is…

A: GIVEN: Load W= 30KN length of road BC:LBC=0.2m length of road CD:LCD=0.3m  thickness of plate C: t=…

Q: Calculate the values of the Rx for the two parts of Example 17.1 shown below. Boundary layers on…

A:

Q: An L-shaped bracket is supported by a frictionless pin at A and a cable between points B and D. If…

A:

Q: If the principal stresses are of opposite signs, then failure occurs in the plane. True or false?

A: Given: The maximum principal stress is σ1=σ. The minimum principal stress is σ2=- σ.

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A: Need to determine normal stress σn or ( σx )  In the given answer normal stress is shown by σn  Data…

Q: Quiz ch-2 Strain rosette readings are made at a critical point on the free surface in a structural…

A: Strain rosette readings are made at a critical point on the free surface in a structural steel…

Q: Determine the state of stress at point A on the cross section of the pipe at section a - a. Take P=…

A: Data given  P = 6.1 kN  ro = 50 mm  ri = 40 mm

Q: The stresses shown in the figure act at a point in a stressed body. If o = 239 MPa in the direction…

A:

Q: Problem 4-69: The assembly has the diameters and material indicated. If it fits securely between its…

A: To findDetermine the average normal stress in each material when the temperature reaches,…

Q: The nail cutter consists of the handle and the two cutting blades (Eigure 1) Figure 6 mm 6 mm -36 mm…

A: According to the given data F=6 N We need to find Force on the fingernail by the cutter

Q: determine the diameter of the bar DE if the normal stress is limited to 100MN/m2. b) Determine the…

A: Given DataP1=30kN θ=30° {taken}

Q: 15 kips H A B 20 kips C D 20 kips E L J K 6 bays @ 15'-0" = 90'-0" F M 10 kips G 12'-0"

A: Required:FJK ( force in member JK )

Q: Hertz contact theory can be used to determine the stresses due to contact between two spheres, which…

A: It is asked to find the stress by using Hertz contact theory

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.