The assembly has the diameters and material indicated. It fits securely between its fixed supports when the temperature is T₁ = 70°F. (Figure 1) Figure ▼ 2014-T6 Aluminum 12 in. Part C -C 86100 Bronze Ost= 8 in. Submit 6 ft 1 of 1 304 Stainless steel C 4 in. -3 ft- D VO ΑΣΦ 1 ↓↑ ▼ Request Answer ▼ Part A Determine the average normal stress in the aluminum when the temperature reaches T₂ = 125 °F. Express your answer in kilopounds per square inch to three significant figures. Jal = Submit Part B Obr= Submit VAE Ivec Request Answer vec Determine the average normal stress in the bronze when the temperature reaches T₂ = 125 °F. Express your answer in kilopounds per square inch to three significant figures. VG| ΑΣΦ | 11 Request Answer Determine the average normal stress in the stainless steel when the temperature reaches T₂ = 125°F. Express your answer in kilopounds per square inch to three significant figures. → vec ? ? ksi ksi ? ksi

Q: A torque of 18 N m is applied to a rotating part. The part has a moment of inertia of 0.078 kgm2.…

A: Here we will use the the torque equation and the rotational motion equation.

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: The velocity of the piston is 52.9901 3 ft/s.

A: use sine rule

Q: In the figure shown, gear A rotates at 300 rpm. Gear S is fixed and has 80 teeth. The three…

A: Write the given data. Speed of arm, Narm=180 rpmSpeed of anulus gear, NA=300 rpmSpeed of gear S,…

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: Calculate the mechanical advantage of the following compound machine.

A:

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: Cork k =.045 also all are 300 K values ... please resolve

A:

Q: solve 4 and 5 only

A: The given state of stress is:To find:(iv) The orientation of the elements for the maximum in-plane…

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: An engineer is creating a solid model of a simple gear using SolidWorks. Choose the correct…

A:

Q: The objects shown below have been rotated positively about one of the axes shown. the amount of…

A: According to the given data rotation amount and rotational axis is provided in the below picture.

Q: Given a gear of 32 teeth and 6 diametral pitch. Find the pitch diameter, outside diameter, tooth…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: An 4 cylinder engine has a crankshaft sp of 3,500 rpm, a bore of 3.8 inches, a str of 3.8 inches,…

A: Givenk=4N=3500 rpmd=3.8in =3.8×0.0254=0.09652mL=3.8in=3.8×0.0254=0.09652mP=210…

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: solve a thru e show all steps

A: is normal reaction force between contacting surfaces.W is the weight force of the block. is the…

Q: For practical working gears as manufactured, typically the addendum, a, is larger than the dedendum,…

A: Addendum: The distance between the top land and the pitch circle on a gear tooth, is called as…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.