QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating gear and the spur gear has the diametrical pitch of 10, pressure angle of 200, and 80 teeth, determine a). The resultant force exerted on the shaft = Ib 2) If it carries a sprocket that delivers 4 hp to a mating sprocket and the sprocket has the pitch diameter of 6", determine b). The force exerted on the shaft Ib 3). If it carries a "flat-belt pulley" (Note: NOT V-Belt Drive) that delivers 8hp to another flat-belt pulley and the pitch diameter of the pulley is 20", determine C). The force exerted on the shaft =

QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating gear and the spur gear has the diametrical pitch of 10, pressure angle of 200, and 80 teeth, determine a). The resultant force exerted on the shaft = Ib 2) If it carries a sprocket that delivers 4 hp to a mating sprocket and the sprocket has the pitch diameter of 6", determine b). The force exerted on the shaft Ib 3). If it carries a "flat-belt pulley" (Note: NOT V-Belt Drive) that delivers 8hp to another flat-belt pulley and the pitch diameter of the pulley is 20", determine C). The force exerted on the shaft =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5.6. a) Consider the limits of integration while solving this problem. The larger (upper) limit of integration for the Q direction is _____ rad. b) Consider the limits of integration while solving this problem. The smaller (lower) limit of integration for the Q direction is _____ rad. c) Consider the limits of integration while solving this problem. The larger (upper) limit of integration for the radial direction is _____R. d) Consider the limits of integration while solving this problem. The smaller (lower) limit of integration for the radial direction is _____R. e) For this question ONLY, let R=73mm. The x-coordinate of the centroid is _____ mm. f) For this question ONLY, let R=73mm. The y-coordinate of the centroid is _____ mm.
Find the value of the dedendum for a 20 degree full-depth involute (coarse pitch) gear with a circular pitch of 7.5 inches per tooth. A 2.93 B 2.87 C 2.78 D 2.39
4.) Find the angle at which the compound rest is to be swivelled or set with the following data: a) Tapered portion of the work = 100mm b) Smaller diameter = 50mm c) Larger diameter = 75mm
the radius of each pulley is 5 inches and the coeffiecent of friction is 0.3 a) determine the largest torque that can be transmitted if the allowable belt tension is 1000 lbs? b) what would be the largest torque if the belt is a v-belt with a groove angle of 75 degrees? c) which style belt transmits the highest torque a flat belt or a v belt?
8. Solve for Sin, Cos, and Tan for angle A with the diagram below for angle A. (Use Machinery's Handbook for Equations) Page # A.) SIN B.) COS C.) TAN a A b
Solve this one correct. I will rate your answer
3- A loaded structure with a two-dimensional stress state has the stress in the x-axis is 13.5 Mpa, in the y-axis is - 3.2 Mpa, and the shear stress in the x-y is - 4.4 Mpa. a) Write the stress transformation equations b) Calculate o and t for the inclination angle 0 between the n values 0 to 180°, in 15° increments. c) Draw the profile graph of normal stress and shear stress with e in the x-axis d) Obtain from the graph, the principal stresses o,, o,, and 2' maximum and minimum shear stresses Tmax and tmin e) Obtain from the graph the corresponding inclination angle Op1, Op2, Os1, and es2 for each of principal stresses and shear stresses, respectively
a)Normal stress due to bending caused by V. Enter your answer in MPa b) Shear stress caused by T. Enter your answer in MPa c) Apply the Maximum-Distortion-Energy Theory and calculate Mises equivalent stress. Enter your answer in MPa d) Determine the factor of safety n.
Question 5 The hollow steel shaft has an allowable shear stress of [T] MPa. g) Determine the largest torque that can be applied to the shaft. Upload 1.5 m Choose a File 60 mm 40 mm
B).shear stress caused by T C).APply miaximum-Distortion-energy Theory and calculate Mises equivalent stress. Enter your answer in MPa to 2 decimal places. D). determine factor of safety n (upto 2 decimal places)
Question 1 Pulleys A and B with the dimension of 66 mm in diameter are connected to solid shafts AB and BC, respectively as shown in Figure 1. The red arrow printed on pulleys A and B are the direction of rotation of the torque. If the force applied to pulley A is 5 kN and to pulley B is 5 kN, Compute: 30 mm - a) The maximum shearing stress in the shafts AB and BC. 46 mm C b) The angle of twist for at end A with the modulus of rigidity 26 GPa. Figure 1
The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are rotated through 180°? Assume the radius of the bicycle wheel is 12.7 inches. The bicycle will travel approximately (Round to the nearest tenth.) in. C -1.95 in 4.21 in