In the gear train shown gear 3 is carried on arm 5, Gear 3 meshes with gear 2 andgear 4. The number of teeth on gear 2, 3 and 4 are 60, 20, and 100, respectively. Ifgear 2 is fixed and gear 4 rotates with an angular velocity of 100 rpm in thecounterclockwise direction, the angular speed of arm 5 (in rpm) is4235

Here, Gear 2 is sun gear. Gear 3 is planet gear. Gear 4 is annular gear. Link 5 is arm. From the…

Answered: In the gear train shown gear 3 is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please do fast
Q5 For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm. The number of teeth for each gear is as follows: NA = 60 Teeth, Ng = 84 Teeth, Nc=36 Teeth and Np = 60 Teeth. - Calculate the output angular velocity at Gear D (wp).Give your answer in rads to the nearest radian. Gear D is the output gear for the simple gear train shown below. Gear B Gear A Gear D 84 60 60 Gear C 36 Input Gear A (2500 rpm) Output Gear D
Two internal 10-pitch, 20° full-depth gears are used in a system. The pinion has 28 teeth and the gear has 70 teeth. Determine the center distance.
A gear train is designed to reduce the speed of the wheel as shown The information of the gears is also listed Motor Gear Number of teeth 12 48 C 12 C 28 Wheel 12 2" diameter F 48 a). If the speed of the motor is 3000 rpm, what would be the speed of the wheel? rpm. b). If the tangential velocity of the wheel is required to be 24 ft/min. what would be the required speed of the motor? rpm Wheel 2" diameter 24 ft/min
For the gear train in a watch shown in the following figure. The teeth number of each gear is z1=8, Z2=60, Z3=8, zZ4=64, Zs=28, Z6=42, Z7=8, Zg=64. Please calculate the ratio of second hand and minute hand. Second Hand 3 Minute 8 Hand Hour Hand
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A gear reduction system consists of three gears A, B, and C. Gear A rotates clockwise with a constant angular velocity wA = 1200 rpm. 2 in 2 in. 4 in. 6 in. Determine the angular velocities of gears Band C. The angular velocity of gear Bis| The angular velocity of gear Cis [ rpm O rpm 0
Problem 2. A compound gear train as shown in the following figure, Gear 1 has 24 teeth and Gear teeth of diametral pitch of 4. Gear 3 has 30 teeth and Gear 4 has 50 teeth of diametral pitch of 3. Gear 1 turns 12 rpm in clockwise direction. 2 has 70 (a) Computer the speed and direction of the shaft carrying Gear 4. (b) Find the torque at Shaft c if the input horsepower at Shaft a is 50? Shaft b Shaft c Shaft a Gear 1 Gear 2 Gear 3 Gear 4
A driving wheel of a gear has a radius of 20 cm and driven gear has 9 teeth along its circumference. If the driven wheel makes 5 rotation for every one rotation of the driving wheel. Calculate the rear ratio and diametral pitch
An epicyclic gear in figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the Centre of the ring gear at 20 rpm. If the gear A is fixed, Calculate the speed of planet gear.
The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to accelerate a flywheel at 0.1 rad/s2. The input gear has 11 teeth, and the output gear has 99 teeth. What is the flywheel's inertia? T=3N O O Input gear 11 teeth. Output gear 99 teeth 270 kgm² 57 kgm2 2.7 kgm2 Don't Know 27 kgm2 Flywheel 0.1 rad/s²
In a reverted epicyclic gear train, the arm A carries two gears B and C and a compound gear D - E. The gear B meshes with gear E and the gear C meshes with gear D. The number of teeth on gears B, C and D are 75, 30 and 90 respectively. Find the speed and direction of gear C when gear B is fixed and the arm A makes 100 r.p.m.clockwise. D В г A
The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating at a speed of 1200 revolutions per minute. It must increase the torque received at its input shaft 16 times. Spur gears with 20° pressure angle should be used. Input and output shafts should be aligned. The transmission should take up as little space as possible. The distance between the centers of the input shaft and the intermediate shaft (the one that loads gears 3 and 4) should be 10 inches. Determine the magnitude of the radial load that gear 4 exerts on gear 4. Write your answer in pounds.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS