In the figure below, Gears B and C represent a compound gear and have the following details. The input Torque is 42Nm and the gear system has an efficiency of 72%. If Gear A rotates clockwise at 2400 revs/minute (gear D has been worked out as rotating 24000 revs/minute) calculate the output power and fixing torque.

Q: The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A…

A:

Q: Q3: For the gear trains shown below, What is the velocity and direction of output gear? A 60T D 201…

A: . GivenTA=20NA=60rpmTB=60NB=?TC=10NC=?

Q: Epicyclic gear box is shown in Figure.2, the gear box has outer gear C with 120 teeth, B has 50, D…

A:

Q: n a compound train of gears spur gear 1, with 40 teeth and rotating at 15 rpm, drives a pinion 6…

A:

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: 2. The spur gear train drive shown in question 1 (as bearing D and E) fitted with full journal…

A:

Q: A gear box has an input speed of 2,000.00 rev/min clockwise and an output speed of 500.00 rev/min…

A: Given data, Nin = Input speed = 2000 rev/min Nout = Output speed = 500 rev/min Pin = Input power =…

Q: The figure below represents a pair of spur gear fitted on a lathe machine. A power of 6 kW at 657…

A:

Q: A pinion with known module and number of teeth rotates at 2400 rpm and drives a gear at 800…

A:

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: (Pinion) Gear 2 Idler N2 = 75 teeth Gear 3 Output N3 = 25 teeth O teeth he following: 1. Pinion…

A:

Q: The gear train shown in the image has a pressure angle of 20° and a DP of 16. Shaft 2 is turning at…

A:

Q: A two-stage gear train consists of four gears meshed together (Figure 10). The secondand third gears…

A: for the given gear train  To determine  angular velocity of gear 4 in terms of ω1,n1,n2,n3 and n4

Q: For the gear train shown below determine the velocity ratio, output speed, output direction, output…

A: Given:  No. of Teeth in Gear A, ZA = 20 Rotational Speed of Gear A, NA = 3000 rpm  (CW) Input Torque…

Q: If there are three gears A, B, C number of teeth in A is 32, B is 45, and C is 48. B is the idler…

A:

Q: culation of Geartrains (3) NA = 20 Input Shaft 1 Only pitch circles of gears shown BNg = 70 Ne= 18…

A:

Q: 18. A wormgear set has a single-thread worm with a pitch diameter of 1.250 in, a diametral pitch of…

A: WORMGEARING DATA FROM PROB. 8-52:To=924 LB.IN.) MG-30rem FORCES: W+G=Wxw = To / (06/2) = 924 28-IN.…

Q: The figure shows a pair of shaft-mounted spur gears having a diametral pitch of 5 teeth/in with an…

A: The force acting on bearing .

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: Problem 2. A compound gear train as shown in the following figure, Gear 1 has 24 teeth and Gear…

A:

Q: An epicyclic gear in figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72…

A: Given Data Ts=32 TR=72 Y=+20

Q: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

A: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

Q: Referring to the given figure, spur gear A receives 5 hp at 650 rpm thl B is an idler and gear C is…

A:

Q: The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to…

A: Given data: Input gear teeth = z = 11 Output gear teeth = Z = 99 Assuming that  Input gear torque =…

Q: In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast…

A: We can answer up to 3 sub-parts so we will answer first 3. Please resubmit the question by…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.