The figure below represents a pair of spur gear fitted on a lathe machine. A power of 6 kW at 657 rpm has to be transmitted by a motor shaft, which is input at pinion gear and its shaft rotates in The number of teeth on pinion and the gear are 29, and 72 respectively, while the module is 8 mm. Assume a pressure angle of 20°. Calculate, the torque on the shaft of the pinion and the gear.

Q: pair of spur gear fitted on a motor shaft of lathe machine transmits the power of 7 kW at 600 rpm…

A:

Q: led to the input shaft of the pinion (or driver) Gear A as shown in Figure Q4a. Calculate the torque…

A: given: W=1800W N=650rpm

Q: Epicyclic gear box is shown in Figure.2, the gear box has outer gear C with 120 teeth, B has 50, D…

A:

Q: n a compound train of gears spur gear 1, with 40 teeth and rotating at 15 rpm, drives a pinion 6…

A:

Q: pinion shaft of a machine transmits a torque of 66 Nm to the shaft of gear at a speed of 564 rpm,…

A:

Q: A drive system for a large commercial band saw is to be designed to transmit 12 hp. The saw will be…

A: 1 HP = 745.7 = 746 WATT 12 HP = 12 * 746 = 8952 W = 8.952 KW pinion rotates  NP =  3450 rpm gear…

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

A: Given:- P=3.5kW m=2mm Pressure angle=20° N=1800rpm To find:- g) Torque on gear 4

Q: A 4 module, 20◦ pinion of 36 teeth drives a gear of 72 teeth.  a. Calculate the length of action and…

A: Given data: Pinion Module (m) = 4Number of Teeth (N) = 36 Gear Module (m) = 4Number of Teeth (N) =…

Q: 2. The spur gear train drive shown in question 1 (as bearing D and E) fitted with full journal…

A:

Q: Two spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be…

A: Given Data

Q: A gear box has an input speed of 2,000.00 rev/min clockwise and an output speed of 500.00 rev/min…

A: Given data, Nin = Input speed = 2000 rev/min Nout = Output speed = 500 rev/min Pin = Input power =…

Q: wo spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be…

A:

Q: A pair of iron cast gears connecting two shafts at the Angle of the elbow. The diameter of the…

A: pitch diaDG=100mm=0.1mDP=80mm=0.08mϕ=14.5°σOP=55MPaσOG=55MPaP=2.75kWεP=εG=84kN/mm2

Q: A power of 25 KW is transmitted by a pair of spur gears. Pressure angle= 20, radial force generated…

A: Given, P = 25 kW, θ = 20 0, Fr = 220 daN = 2200 N, N = 600 N, t = 33, Dp2 / Dp1 = 3 We need to find…

Q: A pair of helical gears are machined with a hob. The hob has a 20 degree pressure angle and machines…

A: The pressure angle = 20 degrees The circular pitch, p = 0.55 in/tooth the number of teeth on pinion,…

Q: 18. A wormgear set has a single-thread worm with a pitch diameter of 1.250 in, a diametral pitch of…

A: WORMGEARING DATA FROM PROB. 8-52:To=924 LB.IN.) MG-30rem FORCES: W+G=Wxw = To / (06/2) = 924 28-IN.…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.