(Pinion) Gear 2 Idler N2 = 75 teeth Gear 3 Output N3 = 25 teeth O teeth he following: 1. Pinion (Gear 1) pitch diameter 2. Gear 2 pitch diameter 3. Gear 3 pitch diameter 4. Circular pitch 5. Addenda 6. Center distance from gear 1 to gear 3, 7. Line of action length for gear 1 contacting gear 2,

(Pinion) Gear 2 Idler N2 = 75 teeth Gear 3 Output N3 = 25 teeth O teeth he following: 1. Pinion (Gear 1) pitch diameter 2. Gear 2 pitch diameter 3. Gear 3 pitch diameter 4. Circular pitch 5. Addenda 6. Center distance from gear 1 to gear 3, 7. Line of action length for gear 1 contacting gear 2,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

b) Figure Q1b shows a compound gear train with Gear A as the pinion (or driver) with an input Power (Pin) of 600 W at Gear A. If Gear A rotates at 139.70 rpm and engages with Gear B, calculate the angular velocity (w) in rad/s for Gears B, C & D; and the input torque (Tin) in at Gear A and output torque (Tout) at Gear D. The number of teeth (N) for gears A, B, C & D are 62 teeth, 34 teeth, 42 teeth and 22 teeth, respectively. Assume 100% efficiency and no frictional losses; and give your answers to two decimal places. GEAR A GEAR C GEAR B GEAR D
Figure Q2-1 shows a schematic of the power train for 2012 Nissan Leaf pure electric cars, which includes a two stage gearbox (a compound train). The numbers of teeth of the gears in the gearbox are N1=N3=17, N2=31 and N4=74. The motor speed at an engine power of P = 80 kW is nmotor (n1) = 9,795 rpm. N2=31 T 2012 LEAF Driveline from Motor to Axle: 17T 31T N1=N3 =17 T 17T 74 T - Wheels I N4=74 T Motor Figure Q2-1 What are the necessary and sufficient requirements for the two stage gearbox to mesh properly for power transmission? i) Calculate the rotating speed (nwheel or n4) and the torque Twheel or T4 on the axle of the driven wheels. Neglect power loss of the gearbox. ii) nmotor(n1)=9,795 rpm in kilometre per hour? You may assume the diameter of the wheels to be D = Ø600 mm. What is the speed of the Nissan Leaf car when the motor speed is at AXLE AXLE
A worm drive transmits 15 kW at 2000 rpm to a worm gear having 90 teeth with 6mm module. The worm is triple threaded and has 65 mm pitch diameter. The tooth form is to be 20 degrees full depth involute. Determine: a) the lead and lead angle of the worm A. b) The center distance between worm and gear. c) The tangential force acting on worm. d) The axial force acting on worm e) The radial force acting on worm
4- Find the gearing ratio for the given compound gears shown in figure 10. 5- Given that the torque (t) of the driver gear is (40+x) N.m, find the torque of the green gear. (x is the last digit of your ID) (M) rrrrv Figure 10 Figure 11 D Error
Find the speed direction of gear 7 if gear 1 rotates clockwise. What is the overall the train value?
A spur gear set is cut with a hob. The spur gears have a pressure angle of 20 degrees and a diametral pitch of 16 teeth/inch. The pinion has 32 teeth while the gear has 80. The customer wants to replace the spur gear set with a custom helical gear set. The only requirements are: (1) the same hob must be used (2) the gear set center distance must remain the same (3) the gear ratio must remain the same. The designer has decided to use a helical pinion with 28 teeth. For the helical gear set, select the proper helix angle that will guarantee the three requirements. Report your answer in degrees, 3 decimal places.
Find the gear ratios of given gear systems. z1=10 z=40 z3=7 z4=24 zs=14 zg=18 Giriş 24 26 Z3 OUT Giriş 26 OUT
6. 5 3 Arm 6. 2 Arm Arm 2 3 1 Bearing Given N2 = 30, N3 = 25, N4 =45, N5 = 40, N6 = 200 W2 = 240 rpm ccw, warm = 120 rpm cw, T2 = 12 ft-lb Show your work. Answers without work will not be accepted a. Identify the gear sets. b. Determine the velocity gear train ratio and the angular velocity of gear 6. c. Determine the torque gear train ratio and output torque of gear 6.
In the planetary gear train shown in below figure, Gear A is the driver and gears B and D are compounded.Gears E and C are internal gears with C as the fixed gear.Number of teeth on gears are TA-20;TB-60; Tc-140;TD-40;,TG-120. If the drive gears rotates at 720rpm CCW when seen from the right, find out the speed at which driven gear rotates C140 120 Output D 40 60 20 Input