The shaft from a DC motor is connected to gear A which rotates at 45rps in clockwise direction. Gears B and C are compound gears as well as gears D and E. Gear A meshes with gear B and gear C drives gear D. Gear E meshes with gear F which is mounted on the driven shaft. The number of teeth on gears A, B, C, D, E and F are 21, 35, 49, 63, 56 & 84 respectively. Sketch the arrangement and determine the speed (rpm) and direction of gear F? Calculate the centre distance between the driver and driven shafts if the module of gears is 2.3 mm

Q: The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A…

A:

Q: A gear train is made up of five spur gears as shown in the figure. Gear 2 is driver and gear 6 is…

A: Given data, Figure shown gear train is made of five spur gears. Where,  Gear 2 is driver and gear 6…

Q: n a compound train of gears spur gear 1, with 40 teeth and rotating at 15 rpm, drives a pinion 6…

A:

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A: Pressure angle is 20 degreeNumber of teeth on pinion is 24Number of teeth on gear is 96Pinion…

Q: State an equation tha relate the number of teeth of gear D, B and C.

A:

Q: A gear train is shown below .The gear 'A' is rotating with 1800 rpm and the number of teeth of all…

A: Given:ωA=1800 rpmTA=36TB=18TC=25TD=18TE=30

Q: 1

A: Given data  1. Number of teeth on  Z1=15 2. Number of teeth on  Z2=31 3. Number of teeth on  Z3=17…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: 6. Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Given that,  Two spur gear of 40 teeth and 120 teeth   Pinion rotates at 1200 rpm   Torque is 20 N.m

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

A:

Q: nning at 100 rpm clockwise. B is an output shaft running at 250 rpm clockwise. Torque on A i

A: given:NA=100RPMNB=250RPMTA=50KN-m

Q: For the following differential gear, if the number of teeth is as follows: N = 24, N2 = 48, Na = 18,…

A:

Q: The figure shows a schematic representation of a gear system. The gears are meshed with one another…

A:

Q: Two parallel shafts, about 550 mm apart are to be connected by spur gears. One shaft is to run at…

A:

Q: (Pinion) Gear 2 Idler N2 = 75 teeth Gear 3 Output N3 = 25 teeth O teeth he following: 1. Pinion…

A:

Q: 50 teeth A 90⁰ B 80 teeth C 60 teeth

A: Given,  NA= 700 rpm

Q: The figure shows a transmission consisting of pulleys and gears. The motor (marked in red) rotates…

A:

Q: angular speed of Gear 5 is

A: Given data, Gear 2 rotates at 1200 rpm N2= 1200 rpmIt is engages with gear 3 and gear 4 mounted on…

Q: The gear train has the following properties: Gear 2: N2 = 14 teeth and Pd = 14 Gear 3: d3 = 2.0 in.…

A:

Q: n find the speed of the gear F.

A: Given data: A compound train consists of six gears. the  no teeth on gears as follows:NA=100…

Q: If there are three gears A, B, C number of teeth in A is 32, B is 45, and C is 48. B is the idler…

A:

Q: Question 1 A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4…

A:

Q: culation of Geartrains (3) NA = 20 Input Shaft 1 Only pitch circles of gears shown BNg = 70 Ne= 18…

A:

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: Problem 2. A compound gear train as shown in the following figure, Gear 1 has 24 teeth and Gear…

A:

Q: An epicyclic gear shown in Figure 1 consists of ring gear, planet gear and sun gear. The ring gear…

A: Given Data Ts=32 teeth Tr=72 teeth Arm y=20 rpm

Q: I transm

A:

Q: An epicyclic gear in figure 1 consists of ring gear, planet gear and sun gear. The ring gear has 72…

A: Given Data Ts=32 TR=72 Y=+20

Q: Each of two gears in a mesh has 60 teeth and a module of 6 mm. The teeth are of involute profile.…

A: Data given-  T = 60  m = 6 mm  Arc of contact = 2.5 × circular pitch

Q: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

A: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

Q: For the gear train shown in the figure. Planet gears 3, 4, and 5 are rigidly connected to a common…

A: The speed of gear 1 is 30 rpmN1=10N3=24N4=N5=12N6=20N7=30determine the speed of gear 7 and the speed…

Q: 4- Find the gearing ratio for the given compound gears shown in figure 10. 5- Given that the torque…

A: Given:Number of teeth on smaller gears, Zs=10Number of teeth on larger gears, Zl=20Torque of the…

Q: Select the correct answer. 1- In figure (1) what the type of gear a- Rack and pinion c- Spur gear…

A: As per our guidelines, we are supposed to answer only first three subparts in case of multiple…

Q: which type ot gears have point contact between two mating gears? olect the coect answer * Helical…

A: These questions are based on the concept of gears.

Q: Use the right formula. A 20 degree-pressure-angle, 22-tooth spur gear has a diametral pitch equal to…

A: Given data:The pressure angle of the gear is number of teeth is  and the gear is spur gearDiametral…

Q: i need the answer quickly

A:

Q: lb pair of bevel gears having 20 and 75 teeth are used on axes that intersect at a 90" angle.…

A:

Q: Determine the required torque for each gear.

A: Need to determine the required torque. ( T1 T2 T3 T4 )

Q: Gear 2 Gear 3 Output N3 = 25 teeth Idler N2 = 75 teeth ng: Sear 1) pitch diameter (1 mark) pitch…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.