For the gear train shown in the figure. Planet gears 3, 4, and 5 are rigidly connected to a common concentric shaft and turn at the same rotational speed, w3= w4 = w5. Gear 1 is connected to the input, gear 7 is connected to the output, and gear 6 is fixed. The planet carrier component 2 is connected to neither an input nor an output. a) the speed of gear 7 if the speed of gearl is 30 RPM. b) The ratio between the input and the output. N₁ = 10, N3 = 24, N₁ = 12, Ng = 12, No = 20, N₁ = 30 Component → Operation ↓ all components turn at x rpm Crank is fixed. Gear 6 turns at y rpm Absolute rotational speeds Fixed Input Gear 1 W1 N3N6 N₁N₁ y N3N6 1 2 Gear 6 W6 y x+y Gear 7 W7 x+ W7 x N=N6 N₂N₂ y N5N6 NAN Output y

Q: Calculate the Maximum Y distance on the drawing below: 1.000 O .510 O .500 O 2.009 C .460 2.000…

A: Maximum  Y distance is possible when the right side hole is having minimum diameter. The distance…

Q: Calculate the reaction forces at the origin assuming a fixed attachment point at (x, y, z) = (0, 0,…

A: Given data: F1=350 NF2=420 NF3=540 N Need to determine the reaction forces at origin (O).

Q: 1- How many significant figures are there in the following numbers? 6856 0.0365 53.72 0.01332…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: 4. Find the measure of the missing angle in the triangle below. 95° 35°

A:

Q: Only use autocad please and show every step to create it and i will definitely like the answer.

A: Given:To find:Draw the given drawing in AutoCAD.

Q: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

A:

Q: Determine if the following sketch is Over Defined, Under Defined, Fully Defined.

A: Given :-  Determine if the following sketch is Over Defined, Under Defined, Fully Defined.

Q: 20 Draw the three drops of the following shape:- R120 $28. 120 R60 14 50 20 80 R 20 R26 660 80 40…

A:

Q: 1.Total Area: c a. 53.61 m2 b. 88.57 m2 c. 31.43 m2 d. 62.16 m2 2. X: a. 1.97 m b. 8.68 m c. 5.62 m…

A: Please see the attached detailed solution:

Q: What are the MOST appropriate views needed to properly describe the drawing? Please state the…

A: Given: Drawings of different parts To find: Appropriate views

Q: Q13. For the beam AB shown in the image below, it is supported by a fixed collar (on smooth rod)…

A: a = 2.1 m b = 2.1 m Force F = 160 N Intensity w = 194 N/m find support moment at point A

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First angle…

A: Given question: Draw isometric view of casting, two views (FV and SV) of which are shown in figure…

Q: Can you send me the top, front and right view of the given diagram with correct dimensions

A: The isometric view is given in the diagram.

Q: Can you send me the top,front and right view of the given diagram with correct dimensions

A: Draw the top,front and right view of the given diagram with correct dimensions.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: I need these three parts answered, if you are unable to answer all three parts please leave it for…

A: 4.The number 81073 denotes the CAGE no. as shown in the print. The CAGE code indicates Commercial…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.