Q13. For the beam AB shown in the image below, it is supported by a fixed collar (on smooth rod) support A and a pin support at B. It is subjected to the external force F = 160 N, and two segments of distributed loads, with maximum load intensity w = 194 N/m. The dimensions are a = 2.1 m, and b = 2.1 m. Determine the support moment (in N-m) at point A. Negative sign must be included if the moment is

Q13. For the beam AB shown in the image below, it is supported by a fixed collar (on smooth rod) support A and a pin support at B. It is subjected to the external force F = 160 N, and two segments of distributed loads, with maximum load intensity w = 194 N/m. The dimensions are a = 2.1 m, and b = 2.1 m. Determine the support moment (in N-m) at point A. Negative sign must be included if the moment is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.3P: A fixed-end beam AB supports a uniform load of intensity q = 75 lb/ft acting over part of the span....

See similar textbooks

Similar questions

A beam supporting a uniform load of intensity q throughout its length rests on pistons at points A, C and B (sec figure). The cylinders are filled with oil and are connected by a tube so that the oil pressure on each piston is the same. The pistons at A and B have diameter d1and the piston at C has diameter D2. (a) Determine the ratio of d2to d1so that the largest bending moment in the beam is as small as possible. Under these optimum conditions, what is the largest bending moment Mmaxin the beam? What is the difference in elevation between point C and the end supports?
A fixed-end beam AB supports a uniform load of intensity q = 75 lb/ft acting over part of the span. Assume that EI = 300kip-ft2. Calculate the reactions at A and B. Find the maximum displacement and its location. Repeat part (a) if the distributed load is applied from A to B.
A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
Consider the following values in the given beam above: L1=6m L2 = 2 m L3 = 4 m L4=3m L5=2 m L6=1m W1 = 90 kN/m W2 = 30 kN/m P = 50 kN M = 60 kN-m Point E is an internal hinge W1 B L2 L3 2 m E W2 L5 L6 H
Pls all of them
please answer do not image format
Draw free-body diagrams of column AB and beam BC and joint B by passing cutting planes through the rigid frame an infinitesimal distance above support A and to the right and immediately below joint B. Evaluate the internal forces on each free body.
de The beam shown supports a load that varies uniformly from 250 N/m at the left end to 0 N/m at the right end. The lengths of the beam segments are d₁=2 m, d₂ = 2 m, and d₂ = 8 m. Reactions Determine the reactions at pin A and roller C. Let positive values indicate upward forces. A= C= Internal Load Determine the internal shear and bending moment at a section passing through point D. Use the standard convention for the meaning of positive shears and bending moments. VD= Mp=
I am struggling with this question
3. Use the double integration Method and compute the value of EI at midspan for the beam loaded as shown in the figure. R₁ 6 ft 1000 lb 400 lb/ft <-3 ft →→ 4 ft3 ft R₂
The floor plan of a building is shown in the Figure below. Using the Ultimate Design Load given, (i) Find the total load on column A. (ii) Determine the Maximum moment for beam A-D. -2 m- -4 m -2 m A D C 10 kN/m? 5 kN/m2 5 kN/m2 E F G 10 kN/m2 Floor Plan -5 m -3 m
How can I find: The bending moment relative to both the z and y axis Mz on the cross section as N.mm The second moment area relative to both the z and y axis as mm4