R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius hole all the way through the part 0.63 mm radius hole all the way through the part 0.63 mm diameter hole all the way through the part 38 SCALE 2.000 2.00 F

Q: 1.3 Determine the length of side a and the measure of the two acute angles. 72.0' 67.3'

A: find the side a and two acute angles.

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: A 10 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.1 kN and a…

A:

Q: Calculate the Minimum Y distance on the drawing below: 1.000 C 2.000 Ø.995-1.000 I 6.00 0.008 MABC X…

A: given; net distance(Snet)=6tolerance in first circle(T1)=0.008net tolerance in x from both side…

Q: Calculate the Maximum Y distance on the drawing below: 1.000 O .510 O .500 O 2.009 C .460 2.000…

A: Maximum  Y distance is possible when the right side hole is having minimum diameter. The distance…

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: For the Gage shown find the distance when 20=22.

A: To Find the distance x

Q: Build the following part and report the volume in units cubed. A = 48 B = 51

A:

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A: It is asked to find the volume of the model based on the given dimensions

Q: 1- How many significant figures are there in the following numbers? 6856 0.0365 53.72 0.01332…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

A:

Q: G R.75 00.63 THRU E 01.123 F0.250 T 2.00 1.00 1.38 1.123 mm diameter hole with depth of 0.250 mm…

A:

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A:

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A:

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A: It is asked to find the volume of the model based on the given dimensions

Q: Which best represents the Slope-field and streamlines for dy = y? – 9 dt

A:

Q: On the toleranced rectangle below, state the tolerance within which the top surface must be flat. O…

A:

Q: R1.00 2 50 1 25 0.50 R.625 50 1.00 .50 R.50

A: Question:Step by step answer: (Help with steps in autodesk inventor 2020) Step 1:firstly open the…

Q: +0.15 +0.25 The dimensions for the shaft size are Ø30 –0.25 mm and the hole size are Ø30 - 0.15 mm.…

A: Solution:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.