+0.15 +0.25 The dimensions for the shaft size are Ø30 –0.25 mm and the hole size are Ø30 - 0.15 mm. ) Find the maximum and minimum limits of hole and shaft. i) Find the tolerance for hole and shaft. i) Find the allowance. iv) Also find the type of fit.

+0.15 +0.25 The dimensions for the shaft size are Ø30 –0.25 mm and the hole size are Ø30 - 0.15 mm. ) Find the maximum and minimum limits of hole and shaft. i) Find the tolerance for hole and shaft. i) Find the allowance. iv) Also find the type of fit.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 1RQ: Information such as tolerances and scale can be found in the________ of an engineering drawing.

See similar textbooks

Related questions

Q: The uniform square steel plate has a mass of 6 kg and is resting on a smooth horizontal surface in…

A: m = 6 kg P = 127 N b = 200 mm = 0.2 m θ=50o

Q: There are some incorrect indications in the following Fig.2. a) Re-draw a correct indicated drawing…

Q: Find 150Am 120mm V- 100 mm

A: Consider the below diagram,

Q: Given part in the figure has the following properties ; a) Part sitting on the other part at the…

A: All the dimensions in mm Front View Top view

Q: - The dimensions for the shaft size are o10*00 0.009 mm and the hole size are b 10*0.015 +0.000 mm.…

A: Shaft sizeϕ10-.009+0.00Maximum limit of shaft =10+0.000=10.00 mmMinimum limit of shaft=…

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: Draw back the drawing given with the scale 1:1 on the new drawing paper using all the method on…

A: 1. Draw the horizontal reference line using Drafter to a some extent. 2. Draw the vertical…

Q: Draw back the drawing given with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: Dimension the holes & shafts for the required linear tolerance. Also calculate the hole tolerance,…

A: For Hole: For RC3 : RC stand for Running Fit . The nominal diameter is 2.00 in. Hole tolerance is…

Q: Show your steps and label units on all answers. 1.) Determine the Forces in all the members, and the…

Q: Draw the SECTION VIEW with the scale 1:1 on the new drawing paper using all the method on section.…

Q: 22 70 56 34 44 RS 024 0s-1 Holes Top view Isometric view 26 +34+ 22-4

A: Top View Top view of the object is obtained when we see the object from top. Front View Front view…

Q: The principal stresses of the state of stress.

A: Given:- Principle stress question with solution, To find:- To clear the doubt how -53.13, 26.6, and…

Q: A 30 mm diameter hole is made on a turret lathe to the limits, 30.035 and 30.00. The following two…

A: (1) tolerance of hole = 30.035-30.00 = 0.035 mm tolerance of 1st shaft = 29.955 -29.925 =0.03 mm…

Q: Liquid water enters a cooling tower operating at steady state at 39°C with a mass flow rate of 105…

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Q: Determine larger diameter, for the figure below. All dimensions are in mm) 110.916 Ø40 091 108.517…

A: The larger diameter is 130.916 mm.

Q: Onv Problems 9-29 to 9-32 F 9-29 to 9-32 A steel bar of thickness h is welded to a vertical support…

Q: Q1) For the given workpiece: a- Show the procedure used for finding the length AB and angle C using…

A: Disclaimer: “Since you have asked multiple question, we will solve the first question for you. If…

Q: 1/8 2015 Cengage Learning Refer to the drawing Bracket below. 1. Explain fully the meaning of each…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: In a three-phase separator, gas, oil, and water are separated into layers of different depths. The…

Q: 100 82 20 32 96 Top view Isometrie view

A: Top view Top view of object is obtained when we see object from top. Front view Front view of…

Q: Please can you show the shear force diagrams for the questions 1 to 4

Q: What is the worst-case distance between the bottom surface of the slot and the bottom surface of the…

A: Worst case between the bottom surface of the slot and the bottom surface of the part is the…

Q: Refer to the Ø.750 dimension. A) Where is the tolerance specified ?…

A: 1—position 2 – the shape of the tolerance zone

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

Q: 50 +0.012 mm and the hole size are 1. The dimensions for the shaft size are +0.015 50+0.005 +0.000…

Q: For an ordinary concrete slab to be laid" -3 within tolerance, engineers can only realistically…

A: Given question is related to metrology and inspection We have to complete the expression that is…

Q: You are given a metal rod, cut to a length of 12 in plus/minus .25in. Then you need to cut off 2 in…

Q: Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The…

A: It is asked to find the mass of the model from the given dimensions Material: Vanadium

Q: -0.05 m. The dimensions for the shaft size are 020 -0.10 1. mm and the hole size are O20 Find the…

Q: For the simplified refrigeration/Heat Pump cycle is shown in the Figure, the coefficient of…

A: Given Data:- The Temperature at warm heated space ( TH ) = 25o C The…

Q: A shaft has to be assembled with a hole. The shaft has maximum limit 59.762 and minimum limit 59.56,…

A: It is required to calculate tolerance of hole and shaft

Question

+0.15
+0.25
The dimensions for the shaft size are Ø30 -0.25 mm and the hole size are Ø30 -0.15 mm.
i) Find the maximum and minimum limits of hole and shaft.
i) Find the tolerance for hole and shaft.
iii) Find the allowance.
iv) Also find the type of fit.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The material is Vanadium. (Located in the "Other Metals" folder in the material properties.) A = 1.72 B = 1.4 2.40 1.20 T .75 TYP 1.20 TYP .70 -1.00 TYP A A A+3.25 R.35 TYP -R.65 TYP CBORE FOR 5/16 HEX HEAD BOLT Ø.332 THRU ALL LØ813 V 235 .10- SECTION A-A 23. B B+1
Dimension the holes & shafts for the required linear tolerance. Also calculate the hole tolerance, shaft tolerance, maximum clearance, & allowance DIAMETER: 2.00 INCHES A) TYPE OF FIT: RC 3 C) DIAMETER: 10 mm TYPE OF FIT: H9/d9 Hole Tol: Shaft Tol: Max. Clearance: Allowance: Hole Tol: Shaft Tol: Max. Clearance: Allowance: Hole Tol: Shaft Tol: Max. Clearance: Allowance: Hole Tol: Shaft Tol: Max. Clearance: Allowance: DIAMETER: 1.00 INCHES TYPE OF FIT: LT 2 GOD DIAMETER: 12 mm D) TYPE OF FIT: H7/h6
Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and calculate the true position tolerance. Show your calculations. Please note: Dimensions shown is relative to the actual size As drawn 4XØ0500 -0.312 Oe.005(M A BC C Pattern-4 holes # 2 1.000 # 3 +) 1.500 +)
What is the worst-case distance between the bottom surface of the slot and the bottom surface of the part in the drawing below? B 4.000-4.020 O 1.475 O 1.450 O 2.950 O 1.500 O 1.030 4.00 0.010MABM 1.000-1.010 2.00 A
QUESTİON: Given part in the figure has the followingproperties;a) Part sitting on the other part at the bottom surface.b) Countersink holes diameters axis need to be controleach other. Also center hole need to be always at thecenter with six holes around it.c) Holes at the rectangular element need to be center bythe rectangular element. Rectangular element hassame tolerance at both direction.d) The both set of the holes are need to be controlaccording to main references and each other.Draw the three views of the part by taking the crosssection of the front view. Also fully dimension the part byusing measurement and geometrical tolerances.
I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts, please leave for another tutor to answer. Thank you.
1. The dimensions for the shaft size are o500.012 mm and the hole size are b 500 +0.000 mm. Find the maximum and minimum limits of hole and shaft. Find the tolerance for hole and shaft. Also find the type of fit. 2.What is the unit of surface roughness? Explain the following surface roughness symbol. N4
I need solve this in quickly time please please
Solidworks
+0.10 -0.05 The dimensions for the shaft size are 020 1. mm and the hole size are 020 mm. -0.10 Find the maximum and minimum limits of hole and shaft. Find the tolerance for the hole and shaft. Find the type of fit and draw the diagram for shaft and hole.
Ex. Find 9 f- 120mm 125mm !30m
A shaft has to be assembled with a hole. The shaft has maximum limit 59.762 and minimum limit 59.56, and the hole has a maximum limit 60.24 and a minimum limit 60.04, compute the following: Tolerance of the shaft is Tolerance of the hole is Shaft size according to MMC = Shaft size according to LMC = Maximum clearance = Minimum clearance = Hole size according to MMC = Hole size according to LMC =