A spherical pressure vessel has an inside diameter of 4.9 m and a wall thickness of 17 mm. The0.27] that has a yield strengthvessel will be constructed from a special steel [E = 224 GPa; v =of 250 MPa. If the internal pressure in the vessel is 1410 kPa, determine (a) the normal stress inthe vessel wall. Answer in MPa rounded-off to 1 decimal place.

The given information in the problem is shown in the following attached image:

A spherical pressure vessel has an inside diameter of 4.9 m and a wall thickness of 17 mm. The vessel will be constructed from a special steel [E = 224 GPa; v = 0.27] that has a yield strength of 250 MPa. If the internal pressure in the vessel is 1410 kPa, determine (a) the normal stress in the vessel wall. Answer in MPa rounded-off to 1 decimal place.

A spherical pressure vessel has an inside diameter of 4.9 m and a wall thickness of 17 mm. The vessel will be constructed from a special steel [E = 224 GPa; v = 0.27] that has a yield strength of 250 MPa. If the internal pressure in the vessel is 1410 kPa, determine (a) the normal stress in the vessel wall. Answer in MPa rounded-off to 1 decimal place.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A thin cylindrical pressure vessel with closed-ends is subjected to internal pressure. What is the ratio of circumferential stress to the longitudinal stress.
The storage capacity of a thin cylindrical pressure vessel is 0.028 m³. The cylinder is subjected to an internal pressure of 21 MPa. The length of the cylinder is twice its internal diameter. Determine all the dimensions of the cylinder, if (a) the longitudinal stress does not exceed 160 MPa; and (b) the circumferential stress does not exceed 235 Mpa.
At a temperature of 22.49 °C a 0.49-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 130.94°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 313.69 mm and M = 239 mm. Round off the final answer to four decimal places.
3) At room temperature (20 °C) a 0.8 mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 120 °C, determine (a) the normal stress in the aluminum rod, (b) the change in length of the aluminum rod Bronze: Aluminum: Steel: Area: 1000 mm2 Area: 2000 mm2 Area: 1500 mm2 a = 18.4 x 10-6 E = 103 GPa a = 23.6x 10-6 E = 75 GPa a = 17.3 x 10-6 E = 190 GPa %3D %3D 0.8 mm 100 mm 150 mm 300 mm Bronze Al Steel
At a temperature of 33.01 °C a 0.46-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 138.98°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 304.28 mm and M = 209 mm. Round off the final answer to four decimal places.
The spherical pressure hull of the undersea submarine, under a research study shown in the figure below, has a 1 meter radius with a shell thickness of 30mm. The pressure hull is made of steel having a yield point of 700 MPa. Consider sea water to have a constant specific weight of 10kN/m³. Determine the depth pressure of submergence that would setup the yield point stress in the spherical shell. Use:p = yy, where y is the depth r = 1m t = 30mm comex
The boom AC is a 4-in. square steel tube with a wall thickness of 0.30 in. The boom is supported by the 0.65-in .-diameter pin at A, and the 0.45-in .-diameter cable BC. Neglecting the weight of the boom, determine the tensile stress in the cable (in psi) if P = 4490 lb. Round off the final answer to three decimal places.
A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free before the load is applied. After the load P is applied, the temperature of all three rods is raised by 110°F. Determine the magnitude of the normal stress in rod (1). Answer in MPa rounded-off to 2 decimal places. Rod (1) : E = 105 GPa; a= 22.0 x 10-5/°C A=500 mm² Rod (2): E = 200 GPa; a = 11.7 x 10-6/°C A=250 mm² 2,100 mm 4,400 mm (1) (2) B (2) P= 45 KN 2,100 mm I
At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature eventually reaches a value of 140°C. Determine the normal stress in the aluminum rod. Determine the change in length of the aluminum rod.
A spherical pressure vessel has a 1.33-ft inner radius and 0.19-in. wall thickness. If the working tensile stress of the material is 5594psi, determine the maximum allowable internal pressure (in psi). Add your answer
7m 4 m 4m 4 m 4m 150 kN 100KN 120KN Determine the normal stress in member BC if the section is circular having an outside diameter of 70mm w/ a thickness of 5mm and indicate if the member is in Compression or Tension.
Please solve urgently