The homogeneous disk of mass m is resting on the right-angled supporting surfaces shown. The tension P in the cord is very gradually increased from zero. If the friction at both A and B is characterized by Us = 0.31, what happens first - does the homogeneous disk slip in place or does it begin to roll up the incline? Determine the value of P at which this first movement occurs. Assume = 30° B 0.75r P !mg Answer: P = i

The homogeneous disk of mass m is resting on the right-angled supporting surfaces shown. The tension P in the cord is very gradually increased from zero. If the friction at both A and B is characterized by Us = 0.31, what happens first - does the homogeneous disk slip in place or does it begin to roll up the incline? Determine the value of P at which this first movement occurs. Assume = 30° B 0.75r P !mg Answer: P = i

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

1m radius disk is moving on the inclined surface under no slip condition. the center of the disk has 3m/s velocity and according to the figure, bar BC is pinned to the disk at point C and point B always stays on the ground. 1) find angular velocity of BC. 2) find angular acceleration of BC
The spring has an unstretched length of 25 in. If the system is released from rest in the position shown, determine the speed v of the ball (a) when it has dropped a vertical distance of 11 in. and (b) when the rod has rotated 33°. 30" k = 0.92 lb/in. 10.0 lb T 11" 25"
Pressurized steam at 4 4 0 K flows through a long, thin-walled pipe of 0.64 m diameter. The pipe is enclosed in a concrete casing that is of square cross section and 1.45m on a side. The axis of the pipe is centered in the casing, and the outer surfaces of the casing are maintained at 340 K . What is the rate of heat loss per unit length of pipe?
do fast
do fast
do fast 100 upvotes.
do fast no use Ai answer plz
a. A mass of 2kg ia attached to a spring with constant 32N/m. An external force of 40tcos2tN is applied to the system. i.Find the total displacement if there is no damping. ii. Find the transient displacement if the damping constant is 20 times the instantaneous velocity of the mass.
A 10-inch industrial fire hydrant has a 6-inch diameter fire hose with a 0.77-inch nozzle that discharges a water jet into the air on the right end. The pressure in the hose is 60 psi and the flow rate is 2,236 GPM. What is the resultant axial force (net value only) the water exerts on the nozzle, in pounds? 6-in. Oa. 6,873 pounds Ob. 8,473 pounds Oc. 10,854 pounds Od. 12,926 pounds
T = -25°C A 0.5 m × 1 m double paned window is made of two silica glass panes 1 cm thick, with air in between. Under steady conditions, linear (constant gradient) Outdoors temperature profiles are found in both silica panes, as well as the air. If the room (and the inner surface of h=18Wm²K the inner glass pane) is at a temperature of 25°C, while outdoors it is -25°C with a convection coefficient of 18 W m² K-1, what is the rate of heat loss through the window? What is the rate of heat loss if the room temperature is decreased to 20°C? Finally, what is the rate of heat loss for a room temperature of 25°C, but with one of the panes (and the air) removed? 1 cm 1 cm Room Temperature, 25° C or 20º C 0.5 mm Air, k=0.024 W m¹ K¹ Silica glass, k = 0.90 W m³ K
3/4 roller chain is to transmit power from a 17-tooth drive sprocket to 34-tooth sprocket. Centers of the sprockets are 13 inches apart. Estimate the number of teeth in contact with the chain for the larger sprocket.
(6) The steel pins at A, B, C, and D have a diameter of 0.5 in and a failure shear stress (Trail) of 24 ksi. Pins A and B are in single shear and pins C and D are in double shear. The steel used in links AB and CD has a failure normal stress (σfail) of 60 ksi. For a factor of safety of 3.2, determine the largest load P that can be applied. Note: Remember to check the bearing stresses in links AB and CD caused by the pins. 0.25 in 1 in A C 8 in 12 in ய P