Q4: The figure shows a shaft mounted inbearings at A and D and having pulleys at Band C. The forces shown acting on thepulley surfaces represent the belt tensions.The shaft is to be made of cost iron (class40) using a design factor N = 2.8. Whatdiameter that should be used for the shaftto avoid the failure?6-in D.300 lbf50 lbf27 lbf8 in8-in D.ZB 8 in360 lbf DC6 inx

Answered: Image /qna-images/answer/e451e58f-8d53-4acf-9e9e-c871e6044b43.jpg

Answered: Q4: The figure shows a shaft mounted in…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.3.16P: Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.

See similar textbooks

Similar questions

The value of curvature correction factor k, will be if the spring index is 6. O a. 1.33 O b. 1.08 O c. 0.92 O d. 4.00 The figure below shows the components of normal forces, the value of radial force on the gear wheel due to a tangential force of 642 N is N, Take pressure angle as 14½0. at Pitch P. point Gear driven to 02 The radial force is
Mechanical design A shaft with the following data: 1- The pulley (A) is 1000 mm in diameter and weight 300N. 2- The gear (B) pitch diameter is 600mm and weight -250N. 3- The pulley is keyed to the shaft at 400mm to the left of left hand bearing. 4-the distance between bearing C and B is 1250 mm. 5- The power is 20 kW at 750 rpm. 6- Tension ratio T1 / T2-2.5 7- The shaft d.livers power to a gear placed horizontally in front, the pressure angel of gear is 20. 8- The allowable shear stress is 70N / mm, kt-2 and km- 1.5. Determine: the diameter of shaft
show all solutions and solve both since relate.
Solve show all steps and solution. Use dynamics approach
Solve both and show full solutions for both
None
Q: Figure (1) shows a schematic drawing of a countershaft which is part of the conveyor system and supports two belt pulleys (A & B). The belt tensions are parallel for pulley B and inclincd with angle 45° for pulley A. The pulley A reccives a power from a motor and then delivers to conveyor belt through pulley B. All dimensions are in mm. Required: Design the shaft as shown in figure (1) at points O, A, B & E. Pulley B Material Discharge Material Fead Pulley A Conveyor System -Tail Pulley Gear box- Sepport Belt Motor Drive balt 300 310.5 N 400 46.5 N 150 Figure (1) 250 dia.- 300 dia. 50 N Pulley A Pulley B 270 N Page 1 of 1
solve, show all steps for given solution.
The pedal system shown in the figure is exerted by both an up and down mechanism. These forces are Fmax=350*SN/10 N, Fmin=-150*SN/10 N. It is desired that h/b = 5 seen in the figure. This piece is AISI 1040 and has a maximum tensile stress of 670Mpa and a yield stress of 540Mpa. Known weakening factors are known as kb=ky=kd=0.8. The notch factor for all stresses is assumed to be Kç=1.5. It is desired to last up to its minimum indefinite life at the cross-section measurement point (bxh) shown in the figure. According to Goodman theory, what should be the minimum size (b and h value) of this section in order to meet this condition. SN=89
Draw schematic figures and find max./min. diametrical slip / press mouth for the following four shaft / sleeve combinations: 1 ø150 H7 / m5 2 ø100 H7 / r6 3 ø80 H7 / g5 4 ø50 H7 / f7
a) A line shaft as shown in Figure Q is driven using a motor placed vertically below it. The pulley on the line shaft is 1.6 m in diameter and has belt tensions 7.5 kN and 2.4 kN on the tight side and slack side of the belt respectively. Both tensions may be assumed to be vertical and the weight of the pulley is negligible. If the pulley is overhang from the shaft, the distance of the centre line of the pulley from the centre line of the bearing being 500 mm.6.Figure Q(i) Predict using distortion energy theory, the appropriate diameter of the shaft that failure will not occur if the yield strength, Sy = 370 Mpa and factor of safety is 2.5. (ii) Assuming the maximum allowable shear stress of 42 MPa, find its diameter using maximum shear stress theory. (iii) Comparing the diameters in (i) and (iii) above, which of them would you have used to design your shaft and why?
hello please help me this homework question considering the time limit I have less than 30min

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS