Solve show all steps and solution. Use dynamics approach A winch is driven by a "Belt Drive System" as shown in the following figure. The large pulley (DrivenPulley) and winding drum have a combined mass moment of inertia IL_Pulley+Drum = 1.165 ft lb s².Pulley "B" is attached to the "drive motor" which applies a torque of TM = 40 lb ft to this pulley.Determine the speed of the 250 lb crate after the motor has made 5 revolutions starting from rest. Assumethe mass of the pulley "B" is negligible (i.e. Ig = 0).3 in.Ans. Vcrate= 3.129 ft/s3 7.5 in. and the-4.5 in.

Given : The moment of inertia is The torque is The mass of crate is The radius of crate is

A winch is driven by a "Belt Drive System" as shown in the following figure. The large pulley (Dr Pulley) and winding drum have a combined mass moment of inertia IL Pulley+Drum = 1.165 ft lE Pulley "B" is attached to the "drive motor" which applies a torque of TM = 40 lb ft to this pu Determine the speed of the 250 lb crate after the motor has made 5 revolutions starting from rest. Ass the mass of the pulley "B" is negligible (i.e. Ig = 0). 3 in. 7.5 in. -4.5 in.

A winch is driven by a "Belt Drive System" as shown in the following figure. The large pulley (Dr Pulley) and winding drum have a combined mass moment of inertia IL Pulley+Drum = 1.165 ft lE Pulley "B" is attached to the "drive motor" which applies a torque of TM = 40 lb ft to this pu Determine the speed of the 250 lb crate after the motor has made 5 revolutions starting from rest. Ass the mass of the pulley "B" is negligible (i.e. Ig = 0). 3 in. 7.5 in. -4.5 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: velocity A ball is shot Vertically into the air @ a of 193.20 81/sec. After 4 secs another ball is…

Q: The 2-kg disk is thrown down onto the rough surface with the velocity and angular velocity shown in…

A: Mass of disk, m=2 kgRadius of disk, r=100 mmInitial angular veloicity of disk, ωi=5 rad/s CCWIniital…

Q: 4. Calculate the pressure in psia at the bottom of a spherical tank filled with sauce. The diameter…

Q: The determinant of this matrix a11 a12 a13 a23 %3D a33 is O a11 a12 a13 O a11 + a22+ a33 O a13 a23…

A: Given:- To Find:- Determinant

Q: This disk has a radius of 2.7 meter and a mass of 80 kg. What is the mass moment of inertia about an…

A: The mass of disc is The radius of disc is

Q: 5 and 5.66 For the beam and loading shown, design the cross section of the beam, knowing that the…

Q: Problem 1. Use INA = I, + Ad² for moment of inertia. From the beam and loadings shown. a. Compute…

Q: If cable AD is tightened by a turnbuckle and develops a tension of 1000 N, determine the tension…

A: Consider E is the origin. From the given diagram, the coordinates of A, B, C, and D are (0, 0, 30…

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: To find: The addendum and dedendum. Given: The module is m=2 mm of Pitch circle diameter per tooth.…

Q: PART I. PROBLEM SOLVING Instruction: Solve the following problem. Show your solutions neatly and…

A: vg=14.1889 cm^3/g

Q: 5. Two bars are used to support a load. When unloaded, AB is 5 in. Iong, AC is 8 in. long, and the…

A: The elongation of the A in the downward direction can be calculated using the formula given below…

Q: Please show how to derive cagliotti function.

A: For parameterizing the experimental profile, Caglioti et alequation—originally .'s created for…

Q: The 5 lb box is projected with a speed of 20 ft/s at point "A" up the smooth vertical circular…

Q: A man riding upward in a freight elevator accidentally drops a package off the elevator when it is…

A: Given Drop height = 100 ft Upward speed = 4 ft/s To find Elevator height Velocity and time graph

Q: The bracket is subjected to the two forces shown. Find the magnitude and coordinate direction angles…

A: Given F1 = 250 N F2 = 400 N To find Resultant Direction of the resultant

Q: Problem 5: The energy lost from a 10 cm thick slab of steel is 50 W. Assuming the temperature…

Q: 4. Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while…

Q: If bar AB has an angular velocity AB = 6 rad/sec, determine the angular velocity of BC and the…

Q: For the figure as shown below, find h in cm that will result to a pressure difference (PA PB) of 10…

Q: QI Find the mass matrix and stiffness matrix

Q: PROBLEM 12.13 The two blocks shown are originally at rest. Neglecting the masses of the pulleys and…

A: Let T be the tension in the cable Free body diag of block A mA=250lbθ=30°

Q: Plot V & M equations a

A: Shear and bending moment equations as follows.

Q: Draft a modeling plan for the component as shown

A: Find Draft the given model on isometric graph paper. Note: The dimension of the given object are not…

Q: The two blocks shown start from rest. The horizontal plane and the pulley are frictionless, and the…

Q: The motion of the collar at "A" is controlled by a motor at "B" such that when the collar is at SA =…

Q: iscuss the importance of moment if inertia in linear and rotational motion. b. Engineer design…

A: Moment of inertia does the same job in case of rotational motion , that mass does in case of linear…

Q: 4. Initially, the car travels along a straight road with a speed of 35 m/s. If the brakes are…

A: Given: Intial velocity, u = 35 m/s Final speed, v = 10m/s Time taken, t = 10 sec

Q: reaching a constant speed of 150 m/s. Construct the a-t, v-t, and s-t graphs rocket until t = 20 s.…

A: Given: Rocket A a=20 m/s^2 for t=12s and then constant speed Rocket B a=15 m/s^2 till v=150 m/s,…

Q: The 200-kg snowmobile with passenger is traveling down the hill such that when it is at point A, it…

A: Given At point A Velocity v = 4 m/s Acceleration a = 2 m/s2 Mass m = 200 kg Acceleration due to…

Q: Determinacy O

A: 1.Statistically determinate 2.Mechanism Structure

Q: The reflection is useful to construct all models true O false

A: Correct option is A The reflection is a thinking process involves consciously thinking about and…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

Solve show all steps and solution. Use dynamics approach

A winch is driven by a "Belt Drive System" as shown in the following figure. The large pulley (Driven
Pulley) and winding drum have a combined mass moment of inertia IL_Pulley+Drum = 1.165 ft lb s².
Pulley "B" is attached to the "drive motor" which applies a torque of TM = 40 lb ft to this pulley.
Determine the speed of the 250 lb crate after the motor has made 5 revolutions starting from rest. Assume
the mass of the pulley "B" is negligible (i.e. Ig = 0).
3 in.
Ans. Vcrate
= 3.129 ft/s
3 7.5 in. and the
-4.5 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: To determine :The velocity of crate after five revolution

VIEW

Step 2: The velocity of crate

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 12 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4 A compressor requires 120 kW to run at 240 rpm from an electric motor of speed 750 rpm by means of a V-belt drivę. The diaincter of comp shaft pulley should not be more than 1000 mm while the center distance between the shafts is 2000 mm. Belt speed should not be more than 25 m/sec. Detcrmine number of belts to transmit the power it each belt has cross-sectional arca of 375 mm', density 1000 kg/m' and allowable tensile stress of 2.5 MPa. The pulley groove angle is 40° and coeff, of friction between pulley and belt is 0.25:
a) An engine has a flywheel mass of 8-tonnes and a turning radius of 3 m. The energy fluctuation is 70 KN-m. The average speed of the engine is 160 rpm. Find the maximum speed value. b) A jet engine has a rotor with a weight of 500 N and this rotor rotates at 2400 rpm. Rotor It is suspended in the middle of the C and D bearings with a total distance of 600 mm between them and the center of gravity is rotated. 35 mm above its centre. By calculating the dynamic forces on the bearings, this system perform the balancing.
The compressor mechanism shown in Figure bellow is driven clockwise by a DC electric motor at a constant rate of 600 rpm. In the position shown, the cylinder pressure is 45 psi. The piston weighs 0.5lb, and the coefficient of friction between the piston and the compressor cylinder is 0.1. The weight of all other links is negligible. At the instant shown, determine the torque required from the motor to operate the compressor. (the piston acceleration is 5378 in/s2). Image is provided .
A belt conveyor transports 18 tonnes per hr at 20°. Determine the unit weight of belt material in kg/ply-cm width-m to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum. The 48V DC motor selected has a no-load angular velocity of 800 RPM and a stall torque of 500 inch-pounds. A gearbox has been designed to spin the drum as quickly as possible. Assume that there are no friction losses in this system. The drum is driven by a 72-tooth gear with a diametral pitch of P=8, and is 3D printed such that it has a yield strength in shear of τy = 2500 psi. Assuming that the entire output torque required to turn the drum is produced by the force on one tooth, and that the gear tooth would fail by being sheared off at the pitch circle, determine the required gear face width, b, for a factor of safety of 3. Note that circular tooth thickness, t, at the pitch circle is π / (2P). Repeat for a gear made out of 6061 Aluminum (σy = 35 ksi, τy = 20 ksi). Only do the part for the 6061 gear do not do it for the 3D printed gear
Mechanical
A rack and pinion is a pair of gears that converts rotational motion into translation. As shown in the figure, a torque τ is applied to the shaft. The pinion rotates and causes the rack to translate. The mass moment of inertia of the pinion is I and the mass of the rack is m. Draw the free-body diagram and derive the differential equation of motion
7. A motor is using a pulley system to lift a block. The radius of pulley 1 is r₁ = 500 mm, and the radius of pulley 2 is r₂ = 750 mm. The pulley has a mass of 50 kg, radii shown on the image below, and a radius of gyration ko = 500 mm. The block has a mass of 50 kg and the motor applies a force to the rope of 1500 N. If block A starts from rest, determine the velocity of block A after time t = 3 s. www r₂ M
2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X
The system shown in the figure consists of two masses attached to a massless road and rotates about the vertical axis at O. The system initially rotating freely at the angular speed of 140 rad/s, when a constant couple moment of CO= 8 Nm is applied on the direction shown.a) Find the time required to stop the assembly.b) Calculate the number of revolutions made until the system stops
4а. Show that the torque t = la, where I is the rotational inertia. Consider the pulley system shown in figure 4. Suppose the pulley is made up of a disc with mass Ma and a ring (hoop) with mass M, as shown in Figure 4a. Find the moment of inertia I, of the pulley through the center of mass. 4b. Find the angular acceleration a, of the pulley as a function of Ip, 0, M1, M2, µk. You may assume that there is no slipping between the pulley and the rope and the mass of the rope is negligibly small in comparison with the mass M1, and M2. The coefficient of friction between M2 and the incline is µk with M1> M2. 4c. Mr md MK outer ving (Mr) Central dise (Ma) RI axis at RAzti on X- Sedi on a pullag
The EOM for the following 1-DOF gyroscope is: JÖ + BO + KO = Hw w is the angular velocity of the gyroscope about the input axis, is the angular position of the spin axis, H is the angular momentum stored in the spinning wheel, J is the mass moment of inertia of the wheel about the output axis, B is the viscous friction coefficient about the output axis, and K is the spring constant of the restraining spring attached to the spin axis. Determine the transfer function relating output to the input w. Case K spin axis output axis BOD Go Wheel spins at constant velocity input axis