9. There is a long solenoid (n:turns per unit, radius R and static current I) parallel to z-axis. If a particle of charge q is moving inside, (a) What is the maximum electric field that the particle can experience at speed v? In which direction is it moving at that moment? (b) In case (a), what is the trajectory of the particle like? Explain.

Q: Determine pressure in [kPa] in the cylindrical pressure vessel shown, if the measured hoop strain is…

A: Given, εhoop=500×10-6E=70 GPa=70×109 Paμ=0.33Ri=400 mm=400×10-3 mmt=6 mm=6×10-3 mm Internal diameter…

Q: Could you please use this code to make the graph that you see in the picture. Keep the color of the…

A: The code generates a graph of CO2 emissions for Diesel and Petrol cars based on their position. The…

Q: (PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare…

A: Feedback Solution (1): This feedback control starts with a level transmitter that will measure the…

Q: 13.5 13.2 11. Apply a dia 0.5 at MMC straightness control to the axis of the part above and draw the…

A:

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A:

Q: la) If a 35 tonne block is raised to 110m and then falls to ground level (in generating mode) in 3…

A: 1a) Given         Mass, m = 35 ton = 31751 kg       Height, h = 110 m          Time, t = 3 min…

Q: possible numbers. Assuming link 2 rotates at a constant rate of 180 rpm CW, determine the velocity…

A:

Q: What is the sequence to do to simulate a control system with simulink?

A: What is the sequence to do to simulate a control system with simulink?

Q: Speed reduction, either through gearing or belt-pulley constructs, is an important element in motion…

A:

Q: grees) answer only ten of the following multi choice questions. 1. In CNC machine tools, the motors…

A: Note: “Since you have posted multiple questions ,we will provide the solution only to the first…

Q: Provide the allocation List Draw the Grafcet and obtain the grafcet equation Develop the ladder…

A:

Q: Every time I use this code the two lies come up but they keep on showing up separately. I need one…

A: The average of the best fit lines for diesel and gasoline will be plotted as a single line by this…

Q: FOR A FANUC 6 axis robot Why do we use the “LBL” statement in a program? flow chart

A: LBL statement means label instruction on FANUC teach program.

Q: There is extensive discussion on CNC programming, as well as G codes and M codes.

A: Given: There is extensive discussion on CNC programming, as well as G codes and M codes.

Q: Describe G03 used in a CNC milling machine G-code. The description has toinclude the syntax of both…

A: G03 Code indicates Counter Clockwise Circular Interpolation. G03 code is used in the CNC milling…

Q: Don't Use Chat GPT Will Upvote

A: Given:Initial speed of neutron, vn1​=120m/sNeutron is scattered at an angle θn​=30∘Deuteron is…

Q: Select one: a. Running an NC part program without touching the stock. Ob. The first time that a new…

A: introduction; A dry run is used for testing of machine program by cutting of air.

Q: 1. Sketch the CAVALIER OBLIQUE of the given object. Use corner "A" for orientation.

A: according to the details provided in the question, we need to draw a cavalier view of the given…

Q: 15. Suppose that we have a product that we want to assemble on a product layout system. The job…

A: Find the given details below:

Q: How do you determine W(input)?

A: Coefficient of performance of reversible heat pump is defined as COPR,HP=THTH-TL…