The pipe assembly is loaded as shown in figure 4.4, determine 1. The state of stress at point B and show the results on a differential element located at this point. 2. The principal stresses and the maximum shear stress at point B by using Mohr's circle. Z 300 mm X 300 mm 30 mm B 20 mm 200 mm Section a-a 450 N 300 N

The pipe assembly is loaded as shown in figure 4.4, determine 1. The state of stress at point B and show the results on a differential element located at this point. 2. The principal stresses and the maximum shear stress at point B by using Mohr's circle. Z 300 mm X 300 mm 30 mm B 20 mm 200 mm Section a-a 450 N 300 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.9P: A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be...

See similar textbooks

Similar questions

An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the xy axes, that is, determine crv, tr(_, and t. Show the results on a sketch of an clement oriented at B = 10
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be sy= -1500 psi. Use Mohr’s circle to: (a) Find the stresses acting on the element oriented at an angle ?? = -35°. (b) Find maximum normal and shear stresses and show them on sketches of properly oriented elements.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
2- The state of plane stress is represented by the stress element below. Draw the Mohr's circle, determine the principal stresses, the maximum shear stresses, and draw the corresponding stress elements. Find the rotation angle of element so that the normal stress of 80 MPa turns to tensile stress of 40 MPa?. 50 MPa 80 MPa 80 MPa A 25 MPa 50 MPa
pls give a full handwritten solution and include the mohrs circle diagram and any free body diagrams needed
Q1. For the given cube below, complete the following: 1.find the center, radius (R), principal normal stresses (σ and σ3), max shear stress (Tmax) and draw the Mohr's Circle. 2. Find the stresses on a plane that is rotated 60° clockwise from the horizontal plane. 6PSE IPSF 10pst 60⁰ TOPST IPSF 6PSF
Problem 3: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind that the principal stress is that stress state where the shear stress is zero. That means it is the stress state along the normal stress line in Mohr's space. So, use your Mohr's circle to find the principal normal and shear stresses, and determine the angle from the x axis to o1. 0x = 16 kpsi, oy = 9 kpsi, Ty = 5 kpsi ccw
Please solve all. Both Questions Please.
Q1: A certain point in the mechanical part shown in Figure below. Use Mohr's stress circle to determine: (a) the magnitude and nature of the principal stresses and the inclinations of the principal planes. (b) the maximum shear stress and the inclinations of the planes on which it acts. (c) the magnitude of the normal stress and shear on a plane inclined at 25° counterclockwise to the plane on which the 60 MN/m² stress acts. 50 MN/m² 30 MN/m² 60 MN/m²