The figure shown below represents a V-Belt drive system. Pulley #1 in the figure has a radius of 3 in and is being rotated by an electric motor delivering 5 hp at 1725 rpm. Pulley #2 has a radius of 14 in and is connected to the input shaft of a reduction gearbox having a gear ratio of n = 2.75. The output shaft of the gearbox drives a grain auger. If there is a 16% power loss for the entire V-Belt and reduction gearbox drive system, what torque (expressed in units of lb ft) is applied to the auger shaft and what is the rotational rate of the auger shaft (in units of rpm)? Pulley #1 (Drive Pulley) Pulley #2 (Driven Pulley)

Q: A plane traveled in the wind. The pilot needed to determine the flying angle to compensate for the…

A:

Q: Compute the discharge velocity of air in ft/s if a turbo-compressor is used to compress 18 pounds…

A:

Q: A metal bar at a temperature of 100 deg. F is placed in a room at a constant temperature of 0 deg.…

A:

Q: If an object is moved a distance D in the direction of an applied constant force F, then the work W…

A:

Q: A figure is scaled, using the parallel method with center of and scale factor for how do the links…

A:

Q: Completely solve and box the final answer. Write legibly 4. Compute the required size of the motor…

A:

Q: This is a multi-part question. Once an answer is submitted, you will be unable to return to this…

A: Step 1:The initial velocity of the ski jumper in x-direction is v0​=26m/sThe inclination angle is…

Q: A team of professional thieves wants to knock down a castle wall using a primitive explosive. At…

A: Given: total mass of the explosive(M) = 40 Kg and it breaks into three pieces as shown below:

Q: Note: Show all your calculations steps. A 14-m beam is subjected to a load, the shear force follows…

A: The Rankine turbo generator is a device used to generate energy using heat in the form of fluid. For…

Q: During the General Enhanced Community Quarantine, we were mandated to stay and work from home. We do…

A: Draw a diagram showing the five displacements at home. Here, 3 displacements are between the room…

Q: For the system given in the figure on the right-hand side, where the input is four-unit step i.e., r…

A: givenAs per the Bartleby policy I am solving Part a, b, c and d.

Q: A total of 10,000 BTU have been rejected from the condenser in two minutes. If the cooling capacity…

A: Given data Q=10000 BTU=1.055×107 JV=0.45 m3/minT2=120°F=322 K Here, Q is the heat transfer and V is…

Q: A large gasoline engine uses a heat output equal to 10,000 J to perform work equal to 2,000 J per…

A:

Q: For the planar mechanism of figure below, link 4 serves as slider support which is free to rotate…

A: given data-Angular velocity ∆ω=250 rpmtime ∆t=5 sec

Q: A rock is spit out of a fire. Its initial temperature is 414 degrees. After exactly 8 minutes, it…

A: Introduction: Newton's law of cooling, which is a function of the cooling constant and time, is…

Q: A person is pulled to the right on a sled (total mass of 53.3 kg) across the surface of a frozen…

A:

Q: Find Ixx for the given Plane, where b1 =160m, d1=25m, b2=20m, d2=90m, b3=60m & d3=25 m (Enter only…

A: Given data:-b1=160m, d1=25m, b2=20m, d2=90m, b3=60m, d3=25mArea of section 1, A1=160×25=4000m2Area…

Q: 3. 4. B 凶

A: 1) not A, since it is a NOR gate

Q: 9. There are 9.5 lbs of brass with specific heat of 0.095 BTU/lbm-ºR at a temperature of 295ºF being…

A: Given    Mass of brass, mb = 9.5 lbs      Specific heat, Cb = 0.095 BTU/lbm-ºR    Mass of water, mw…

Q: Cork k =.045 also all are 300 K values ... please resolve

A:

Q: Write a MATLAB program that finds the sum for-25 to 5. (Increment by 5). By using (while „loop)

A:

Q: Determine the following based on the given: a) velocity of point A (in/s), b) the angle of Va with…

A:

Q: If an object is moved a distance D in the direction of an applied constant force F, then the work W…

A:

Q: Find the summation of all positive numbers less than 50 which are divisible on 3 or 7. Taina D

A: 3 or 7 which is divisible less than 50. we can say that

Q: Question 2/ 25S+4 A) Solve the equations: (S+2)(S+7)

A:

Q: Find the velocity at point B as the link rotates counterclockwise such that the speed of point C is…

A:

Q: In the figure, the elevator moves downward with a constant velocity of 2.74 m/s. Determine the…

A:

Q: Using graphical method solve this problem:  Suppose you first walk A in a direction of B west of…

A:

Q: A 90° elbow shown in Figure Q5 (b) is to direct water flow upward into the atmosphere. The water is…

A: For the elbow to be in place, the net horizontal force on the elbow must be zero. The gauge pressure…

Q: 1. When Tom is at x =1m, what is the tensile force in the wire in Newton? If the wire can hold only…

A:

Q: here is the pronblem with the solution but i dont know how the steps to solve it . pleasde help

A: The question in the image is a statics problem about a crank assembly subjected to forces. We can…

Q: A man was standing on one side of the roof of a building 145 meters above the ground and shot a…

A: Given data as per question Height of building =145 m Speed of projectile =53 m/s The angle from…

Q: A 1725 rpm electric motor is to be used to drive a "flat belt" conveyor in a manufacturing facility…

A: The speed of the conveyor belt is, The diameter of the roller is, The number of teeth on the drive…

Q: x(t) x,(t) K2 K, M M2 B, B,

A:

Q: Respond with TRUE if the symbol of the valve shown below is drawn correctly. 9ype here to search Say…

A: Ans- True

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.