Q1:A reinforced concrete tank * has a bottom plate (foundation) which assumed to be sliding (hinge), find the magnitude that used for drawing the Tangential Force, and then find maximum shear force, using the following data: Diameter (D) =9014mm, Height (H)=8000mm, Thickness (t)=335mm,Poisson ratio (v)=0.25, yw=1OKN/m3=1x10-5 N/ mm3

Q1:A reinforced concrete tank * has a bottom plate (foundation) which assumed to be sliding (hinge), find the magnitude that used for drawing the Tangential Force, and then find maximum shear force, using the following data: Diameter (D) =9014mm, Height (H)=8000mm, Thickness (t)=335mm,Poisson ratio (v)=0.25, yw=1OKN/m3=1x10-5 N/ mm3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam with varying load is shown at the figure below. If the beam properties are given, what is the final stress at bottom of the beam at midspan where total losses of the prestressing force is 27% (MPa) Properties: Beam width = 290 mm Beam height = 463 mm Varying load = 19.6 kN/m Span of the beam 10 m Prestressing force = 481 kN %3D eccentricity = 126 mm Wo (kN/m)
A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.6 MPa. Answer must be in kN/m. Given: b = 110 mm and d 160 mm. 280 mm 150 mm
QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at joint D in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected to the beam by a rivet passing through the three bars meeting at joint C. The allowable shear stress and bearing stress are t-60 MPa and o=120 MPa, respectively. a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system. 0.8m Im 0.6m 15 kN В Beam AD 20mm Strut CB 40mm 100mm 40mm 50mm 100mm Detail of joint C Detail of joint A
240 mm 120 mm 240 mm 240 mm 120 mm 240 mm Determine the magnitude of the maximum shear stress at the cross section if V=120 kN. Express your answer in MPa and use three significant figures.
A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.9 MPa. Answer must be in kN/m. Given: b = 130 mm and d = 160 mm. 280 mm b. 170mm
From figure, given E=200 GPa, r=37.5mm, A= 2285mm^2 and I = 3.33 x 10^-6 m^4.Calculate the allowable centric load for the column and the corresponding stress using Euler’s formula by considering the factor of safety is 2.0
2. The cruciform cross-section of a beam is shown. What should be the minimum allowable shear strength of the material if the beam is designed to carry a shear force V= 10 kips? Neglect bending stresses. V 3 in. 1 in. 3 in. 3 in. 5 in. 3 in.
A steel beam, of lengths a = 6 m and b = 3 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q = 3.1 kN/m for AB span; and is constant with q = 3.1 kN/m for BC span. The Young's modulus of steel is 200 GPa. A y, v a 5 mm 200 mm Figure Q.1 9 A B 300 mm b C X
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER Using MOHR CIRCLE, what is the resulting "HORIZONTAL" SHEARING STRESS at the given angle plane point? a. 44.03 MPa b. 64.32 MPa c. 185.68 MPa d. 75.00 MPa
Problem Solving. 1. A 300 mm diameter circular beam carries a uniformly distributed load of w (kN/m) over its entire span. The beam is freely supported at its entire span. The allowable bending stress is 12 MPa and the allowable shearing stress is 0.95 MPa. Determine a. The safe span (L) of the beam in m. b. The safe uniformly distributed load in kN/m. w (kN/m) IO
A steel beam, of lengths a= 6 m and b= 3 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q = 0 kN/m to q = 3.1 kN/m for AB span; and is constant with q= 3.1 kN/m for BC span. The Young's modulus of steel is 200 GPa. Part A Calculate: A y, v a 5 mm 200 mm Figure Q.1 9 S B 300 mm b с X
1. A typical cross-section of a roinforced concrete T-beam is shown in the figure below. The beam is reinforced with eight 25 mm diameter bars in tension zone. For the purpose of analysis, use the effoctive depth of 575 mm. Use f. = 25 MPa and f, = 420 MPa. Determine øM, 1000 mm T100 mm 8-D25 300 mm 575 mm ww G29