The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is O.04 in. Determine the maximum allowable value of P in kips. 0.75 in A B 50 kips 3 in 20 in- 30 in-

The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is O.04 in. Determine the maximum allowable value of P in kips. 0.75 in A B 50 kips 3 in 20 in- 30 in-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure PP1.4-5. The…

A: Given data in question Diameter 1.5 and 1 in Bearing stress 24 ksi Shearing stress 18 ksi To find…

Q: 1. Draw Mohr Circle and answer the following: 150 MPS 55 MPa 70 MPa Consider a point in a structural…

A: Solution:Given: The plane stress element is shown below:Hereσx=70MPa;σy=150MPa;τxy=55MPa

Q: A hydraulic punch press is used to punch a slot in a 0.40-in.-thick plate, as illustrated in the…

Q: A 86-N-m torque is applied to a hollov section shown. Neglecting the effect determine the shearing…

Q: A paper tube is formed by rolling a cardboard strip in a spiral and then gluing the edges together…

Q: A hydraulic punch press is used to punch a slot in a 0.50-in.-thick plate, as illustrated in Figure.…

Q: f the shaft?A

A: We knowμ=Lateral strainLongitudinal strainLateral strain=δddLongitudinal strain=δLL

Q: For the given stress element, draw the Mohr's circle and determine the principle stresses and…

A: σ1 = 30 kpaσ2 = -40 kpaτ = 20 kpaPrincipal stresees are given byσ1,σ2 =σ1+σ22±σ1-σ222+τ2σ1,σ2…

Q: The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given data, u = 1.5 mmv = 4.3 mmc = 710 mmα = 32° β = 58°To find out the shear strain γ at corner Q′…

Q: A solid 1.20 in. diameter shaft is subjected to a torque of T = 230 lb-ft and an axial load of P =…

Q: The differential element above represents the state of plane stress at a pont J steel beam. Which of…

A: Given data: σX=60 ksiσY=-20 ksiζXY=40 ksi

Q: Part A 0.25 in. 5 in. 1 in. 0.25 in -0.25 in. 2.5 in. Determine the maximum axial force P that can…

A: Thickness =0.25inAllowable stress=22.4 ksi

Q: 9.6 Determine the stresses in the two segments of the bar shown. Segment A has a diameter of 1 in.…

A: FOR SEGMENT A DIA = 1.25 IN. LOAD= 10 KIP FOR SEGMENT B CROSS SECTION = 2IN * 2IN LOAD =22 KIP

Q: A cube of material (E 15,000 psi, v 0.25) of side length 2" is shown in the x, y plane. Take x…

A: Change in length of the cube depends on the length of the sides of the cube and the normal stress…

Q: Assume a rod made of a steel with a maximum allowable stress oa = 155 MPa. Can the rod safely…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

The circular shaft shown is subjected to an
axial force P at its free end and a compressive
force of 50 kips at point B. Note that the
shaft is hollow between points A and B. The
allowable normal tension stress is 22 ksi, the
modulus of elasticity is 29,000 ksi, and the
maximum allowable elongation is O.04 in.
Determine the maximum allowable value of P
in kips.
0.75 in
A
B
50 kips
3 in
20 in-
30 in-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. The shaft in the figure below consists of 75 mm diameter bronze segment that is rigidly joint to 50 diameter steel segment. The ends of the shaft are attached to rigid supports (fixed supports). Calculate the absolute maximum shear stress developed in each segment when the torque T = 5.1 kN-m is applied (a = 2 m and b = 1.5 m). Use G = 35 GPa for %3D %3D %3D bronze, and G = 75 GPa for steel. %3D 75 mm 50 mm A Bronze Steel C T a -
please solve and exlain in neat hand writing
For the beam shown below, b = 6 in and h = 14 in. If the beam is subjected to a transverse shear for of V = 8 kip, determine the largest shearing stress in the beam. Express your answer in psi to the nearest whole psi
This is a mechanics of deformable bodies problem
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown.a) Determine the magnitude of the force P for which the tensile stress in rod AB is 100ksi.b) What is the compressive stress at rod BC?
Problem No.1 A solid steel shaft is loaded as shown in the figure. Using G = 83 GPa, determine the required diameter of the shaft if the shearing stress is limited to 94 MPa and the angle of rotation at the free end is not to exceed 3 deg. If the stress defines the size of the shaft, what is the corresponding angle of rotation at the end when the required diameter is used of if the angle of rotation defines the size the size of the shaft, what is the coresponding stress when the required diameter is used? 750 N-m 1200 Nm 2.5 m 2.75m
with FBD please Complete solution thank you
Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB?in micro rad And answer in right and clear way Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
50% Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 32 in., b= 40 in., δ1= 0.225 in., δ2= 0.075 in. Determine the average normal strain along the side AB? Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
A shaft with 15 mm diameter is fixed as shown below. The shaft is made from AISI 1006 cold drawn steel (280 MPa). The applied loading is as follows: F = 0.55 kN, P = 4 kN, T = 25 Nm. (a) Draw the stress elements at point A (top of shaft) and B (side of shaft), indicating the magnitude and directions of the stresses. (b) Find the safety factor at point A and B using both MSS and DE theory. 100 mm A B 15-mm D.