A solid steel shaft is loaded as shown in the figure. Using G = 83 GPa, determine the required diameter of the shaft if the shearing stress is limited to 94 MPa and the angle of rotation at the free end is not to exceed 3 deg. If the stress defines the size of the shaft, what is the corresponding angle of rotation at the end when the required diameter is used of if the angle of rotation defines the size the size of the shaft, what is the corresponding stress when the required diameter is used?

A solid steel shaft is loaded as shown in the figure. Using G = 83 GPa, determine the required diameter of the shaft if the shearing stress is limited to 94 MPa and the angle of rotation at the free end is not to exceed 3 deg. If the stress defines the size of the shaft, what is the corresponding angle of rotation at the end when the required diameter is used of if the angle of rotation defines the size the size of the shaft, what is the corresponding stress when the required diameter is used?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer number 2 only
SOLVES STEP BY STEP, USE TABLE IF NECESSARY
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=34 kips is applied to the assembly at A, two loads of Q=25 kips are applied at B, and two loads of R=37 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 16 ksi. The normal stress magnitude in steel rod (2) must be limited to 32 ksi. The normal stress magnitude in brass rod (3) must be limited to 24 ksi. Determine the minimum diameter (in in rounded to the nearest thousandths) required for rod 2.
At a point on the surface of a machine component the stresses acting on the e face of a stress element are or = 55 MPa and Txy = 30 MPa (see figure). T- 30 MPa a, = 55 MPa What is the allowable range of values for the stress oy if the maximum shear stress is limited to TO = 34 MPa? Round to one decimal place. (a) Lower limit is MPa (b) Upper limit is MPa
Question 3 A pair of lateral load is applied to a 3 m steel beam as in Figure Q3a to bend it plastically. The beam has a solid rectangular cross-section (30mm x 50mm) as in Figure Q3b. The steel behaves in elastic-perfectly plastic behavior with Yield Stress of 200 MPa. When 50% plastic condition at critical section, determine: a. the value of load P b. the Yielded Length, Lp corresponding to condition in part (a). 1.5P P 1m 1m Figure Q3a 1m 30mm 50mm Figure Q3b
Define particular volume, specific gravity, and viscosity. Include Newton's law of viscosity as well.
ANSWER THE PROBLEM QUESTION AND SHOW YOUR SOLUTION CLEARLY AND BOX THE FINAL ANSWER. USE 2 DECIMAL PLACES
The following composite shaft is loaded as shown in the figure. The AC segment of the shaft is solid; it is connected to the hollow shaft CD with the help of a rigid flange at C. A torque of 100 Nm is applied at B, as shown. A uniformly distributed torque of 200 Nm/m is applied over the entire length of CD (2m), also shown in the figure. Please ignore the thickness of the rigid flange at C. Given: GAC = 140 GPa, diameter of AC = 20 mm. GCD = 200 GPa, inner diameter of AC = 40 mm, outer diameter of AC = 50 mm. a. Determine the absolute maximum shear stress on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Draw the state of stress on a volume element corresponding to the maximum absolute shear stress location. Show proper perspective when drawing the state of stress. b. Determine the absolute maximum shear strain on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Be careful…
1.4