The solid shaft shown is made of a steel that is assumed to be elastoplastic with Ty= 145 MPa and G= 77.2 GPa. The torque isincreased in magnitude until the shaft has been twisted through 6°; the torque is then removed. After the solid shaft has been loadedand unloaded, a torque T₁ of sense opposite to the original torque T is applied to the shaft. Assuming no change in the value of Øy,determine the angle of twist ₁ for which yield is initiated in this second loading and compare it with the angle y for which the shaftstarted to yield in the original loading. Take L = 0.66 m.L16 mmBThe angle of twist ₁ is 8.33.The angle of twist Oy is 4.4391 °.

Answered: Image /qna-images/answer/086de128-1f3c-4db0-a707-9c989c249b6d.jpg

The solid shaft shown is made of a steel that is assu increased in magnitude until the shaft has been twis and unloaded, a torque T₁ of sense opposite to the determine the angle of twist 1 for which yield is init started to yield in the original loading. Take L = 0.66 L 16 mm The angle of twist ₁ is 8.33 The angle of twist Oy is 4.4391

The solid shaft shown is made of a steel that is assu increased in magnitude until the shaft has been twis and unloaded, a torque T₁ of sense opposite to the determine the angle of twist 1 for which yield is init started to yield in the original loading. Take L = 0.66 L 16 mm The angle of twist ₁ is 8.33 The angle of twist Oy is 4.4391

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

torsion
M E You have 2 Thank You Best Regare Ms. Nur Akr Figure Q3 shows a truss structure, which is pinned at A and roller supported at B. Horizontal load are applied to the truss as shown in the Figure. By using section method, solve the force in member AC, CD and DE in the figure shown (CO2, PO2, C3). 20KN 10KN 3.5m H →10kN 3.5m E 3.5m D H 15kN 10kN- 5kN G C A 5.0m 3.5m B 000 5kN 5kN Gmail M
A hollow shaft made of red-brass copper (G = 37 GPa, shear yield strength = 150 MPa) is sandwiched between two solid shafts made of the same material. End A is fixed to a rigid wall and torques are applied to the shaft as shown. 75 kNm d₂160 kNm A d₁ L₁ B Use the following values in your working out: L₂ L₁ = 1.5 m L3 = 2.2 m d₁ = 1 m d₂ = 0.7 m d3 = 1.2 m C d₂ 3 L3 130 kNm D a) Draw a torque diagram for the entire shaft. b) Determine the maximum allowable inner diameter for the hollow section of the shaft, to the nearest mm. c) Determine the maximum length of L₂ (to the nearest mm) that will ensure the angle of twist of D relative to the wall is less than 2°. Use your value from part b for the inner diameter of the hollow shaft. d) By estimating relevant load(s), dimensions, and material properties, calculate the approximate angle of twist between two (non-coincident) points on the object shown below. Clearly state all assumptions, including the location of the chosen points.
The A-36 steel bolt is tightened within a hole so that the reactive torque on the shank AB can be expressed by the equation t = (kx²) N• m/m, where x is in meters. If a torque of T = 50 N · m is applied to the bolt head, determine the constant k and the amount of twist in the 50-mm length of the shank. Assume the shank has a constant radius of 4 mm. B >T = 50 N•m 50 mm dT = t dx 0.05m SON.M
8) If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of force P. The wire BC is A36 steel and has a diameter of 3 mm. 200 G Pa E A36 400 mm 300 mm B 200 mm-
Note: hand written solution is not allowed.
Two plates with a thickness of 35mm, width of 160mm, and length of 200mm are joined together by a pin with a diameter of 60mm. 200 mm 60 mm P 160 mm T 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250MPA and the shear strength of the pin is 100MPA. Suppose that P is 140KN, the Modulus of Elasticity is 200GP,, and the Poisson's ratio is 0.3. 2) Determine the change in length of each plate. 3) Determine the change in width of each plate. 4) Determine the change in thickness of each plate.
Determine the magnitude of the pin force at A. Assume W = 895 lb, a = 2.8 ft, b = 2.1 ft, r = 9 in. a C B А W D Answer: A = i Ib
Determine the shear lag factor of the connection shown in the figure.
!
A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of 12 inch in diameter, and four – ¾ inch aluminum bolts on a concentric bolt circle 8 inches in diameter. With an applied torque of 260 kips*inch. determine the max shearing stress in the aluminum and steel bolt. Use Gst = 12x10 6 psi and Gal = 4x106 psi
In the assembly shown. the block has a weight w = 200 lbs and the cord is attached to the pin at B. The pulleys have radi of rt = 2 Tn. and r2 1 În. Neglect the mass of the pulleys and the link. Pulley Pulley A 45 12 Compute the reaction at the ĩnk AB In lbs." 250 260 280 B.