A paper tube is formed by rolling a cardboard strip in a spiral and thengluing the edges together as shown in (Figure 1). The paper is 1.9 mmthick and the tube has an outer diameter of 100 mm.Figure200 N40°100 mm1 of 1200 NDetermine the shear stress acting along the seam, which is at 50° from the horizontal, when the tube is subjected to an axialcompressive force of 200 N.Express your answer to three significant figures and include appropriate units.■μÅTa'y' = 316.39kPaSubmit Previous Answers Request AnswerProvide Feedback?X Incorrect; Try Again; 9 attempts remaining

Answered: Image /qna-images/answer/20998724-a130-4147-919d-f3e1686b9812.jpg

Answered: A paper tube is formed by rolling a…

A paper tube is formed by rolling a cardboard strip in a spiral and then gluing the edges together as shown in (Figure 1). The paper is 1.9 mm thick and the tube has an outer diameter of 100 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using the Stress-Strain diagram for polymers below, identify the types of polymers depicted based on their Stress-Strain behavior/curve 60 A 50 40 30 В 20 C 10 1 2 4 5 6 7 8 Strain A. [ Choose ] B [ Choose ] [ Choose ] > 3. Stress (MPa)
An aluminium alloy bar of circular cross section as shown on the figure is loaded by tensile forces, P. The length and diameter of the bar are 3.0m and 30mm, respectively. If the bar elongates by 7.5 mm, what is the decrease in diameter Ad? What is the magnitude of the load P? Its modulus of clasticity E=73 GPa and Poisson’s ratio=1/3. (
Please annotate the attached image to highlight the different phases of a polymer stress/strain graph. From the attached graph, calculate the following: 1-modulus of elasticity 2-tensile strength 3-the ductility in % of elongation 4- yield strength at a strain offset of 0.002
In a tension test, a 105 N.cm work is done to break a 30 cm long glass rod with a 4 mm x 75 mm cross-section area. Modulus of elasticity of glass is 7x10° N/cm?. (Assume linear elastic behaviour of glass until rupture) a) Determine the tensile strength of glass. b) Calculate the length of the glass rod at rupture.
The stress-strain diagram for a metal alloy having an original diameter of 16 mm and a gauge length of 300 mm is given in the figure. Determine approximately the modulus of elasticity for the material, the load on the specimen that causes yielding, and the ultimate load the specimen will support. a (MPa) 700 600 500 400 300 200 100 € (mm/mm) 0 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.001 0.002 0.003 0,004 0,005 0.006 0,007
I need the answer as soon as possible
2. A polymer muterial is subjected to a constant load for a set amount of time and then the load is removed. This experiment generates the stress versas time plot and the strain versus time plot shown below. Describe what is happening to the material at following locations on the strain versus time plot below: • At point A • Between point A and point B • Between point B and peint C • Between point C and peint D Briefly comment on how you would expect this strain versus time plot to change if the experiment was carried out en anather sample of the same polymer at a temperature below the polyrmer's glass transition temperature. Time, t в A D Time, t Strain, ɛ Stress, o
For material, the modulus of rigidity is 100 GPa and the modulus of elasticity is 250 GPa. The value of the Poisson's ratio is
A brass alloy rod having a cross sectional area of 0.24 in.2and a modulus of 16 * 106 psi is subjected to a tensile load. Plastic deformation was observed to begin at a load of 8,944 lb.a. Determine the maximum stress that can be applied without plastic deformation.b. If the maximum length to which a specimen may be stretched without causing plastic deformation is 3.28 in., what is the original specimen length?
A 4-m-long steel plate with a rectangular cross section (10 mm * 50 mm) is resting on a frictionless surface under the sun. The plate temperature is meas-ured to be at 40°C. The plate is then moved into a cold room and is left to rest on a frictionless surface. After several hours, the plate temperature is meas-ured to be at 5°C. The steel has a modulus of elasticity equal to 200 GPa and a coefficient of thermal expansion equal to 1.1 * 10-5m/m/°C. a. What is the length of shrinkage?b. What tension load is needed to return the length to the original value of 4meters?c. What is the longitudinal strain under this load?
Consider a rectangular specimen of aluminium has a dimension of 10 ?? × 12.7 ?? is pulled in tension with 35500 N. Calculate the resulting strain. Given the modulus of elasticity is 69 × 103??? and assume that the deformation is elastic.
3. An aluminum material element experiences a state of plane stress with the magnitudes and directions of the stress components given in the figure. Please calculate the change in volume per unit volume this material element would experience when subjected to the stress state given in the image below and a temperature increase of 80°C. (Note that the dotted horizontal line and 15 degree angle are irrelevant to this problem). Aluminum Properties: Thermal Coefficient of Expansion = 24 x 10-6 mm/mm/°C, Elastic Modulus = 69 GPa, Poisson Ratio = 0.35 250 MPa 60 MPa 15° 150 MPa