A concrete beam prestressed with a parabolic tendon is shown in the sketch. The eccentricity of the tendon is measured from the centroid of the cross-section. The applied prestressing force at service is 1620 kN. The uniformly distributed load of 45 kN/m includes the self-weight. 7300 Sectional elevation 750 Cross-section (tendon not shown) All dimensions are in mm The stress (in N/mm2) in the bottom fibre at mid-span is

A concrete beam prestressed with a parabolic tendon is shown in the sketch. The eccentricity of the tendon is measured from the centroid of the cross-section. The applied prestressing force at service is 1620 kN. The uniformly distributed load of 45 kN/m includes the self-weight. 7300 Sectional elevation 750 Cross-section (tendon not shown) All dimensions are in mm The stress (in N/mm2) in the bottom fibre at mid-span is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. For the stress state below, find all three principal stresses and three maximum shear stresses. Draw a complete Mohr's three-circle diagram. Given the stress state: 0xx (cw). 50 MPa, oz = -20 MPa, txy 30 MPa [Hint: Following the procedure in the in-class example problems done by the instructor.]
3. Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional area of each bar so the bars fail at the same time with the load is P = 4 kips. Use a factor of safety of 1.8. 3 ft 4 ft P B σ (ksi) 25 20- 15 10- 5H 0 0 tension. compression 0.20 0.40 0.60 0.80 e (in./in.)
please answer asap
Please show all steps
A simple pin-connected truss is loaded and supported as shown. The load Pis 240 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 14 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 10 m, b = 6.25 m, and c= 5 m. Tensile stress is positive, while compressive stress is negative. b D Answer: OAB 11 JAC OBC= OBD = OCD = i M M a B MPa MPa MPa MPa MPa
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ? P steel raid steel sF I A=0-1 Mat 50°d E = 200 GPa -Aluminum L= 250 Mm A = 1600 mm ² X = 12 x10%2 Call = 200 MPa Comp Alumivun Post. E = 73 GPa A = 2400 mM 400 mM 40o mm 2 X = 23 x 10% T = 150 MP Comp Figure 2
Solve this question as soon as I upvote solution
A) Determine the lateral strain B) Determine the axial strain C) determine the poisson’ts ratio V. COMPLETE SOLUTION. THANKS!
A rectangular plate is subjected to uniform biaxial stress with x = 90 MPa (tension), oy = -20 MPa (compression), and ₂ = 0. The plate has original dimensions 400 X 800 X 200 mm (x X y X z) and is made of steel with E = 200 GPa and v = 0.3. What are the strains Ex, Ey, and Ez?
3. Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load P=75 KN is applied. Neglect the deformation and mass of the horizontal bar AB. Use Ea = 75 GPa, as=23.0 um/m-°C, Aa = 850 mm2 Es = 210 GPa, as = 11.9 um/m-°C and As = 650 mm² . %3D %3D Steel Aluminum 3m 2.5m 3 m 3 m 3 m 75 KN
STRESSES 1. A 150mm x 50mm board is glued to a triangular board. Determine the maximum shear stress of the adhesive IN BEAM material used to connect the boards. 20 KN 1 m 30 KN/m 150 mm 50 mm 1 m 1 m 15 KN/m 250 mm 15 KN/m 2 m 350 mm
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i