240 mm 120 mm 240 mm 240 mm 120 mm 240 mm Determine the magnitude of the maximum shear stress at the cross section if V=120 kN. Express your answer in MPa and use three significant figures.

Q: A beam supports has been shown in the bellow figure. The material is gray cast iron. The value of…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: Given Mohrs circle:As each grid square is 2 ksi in size

Q: A flat steel bar, 29 mm wide by 4 mm thick and 1.8 m long, is bent by couples applied at the ends so…

A: Given data in question  Cross section Length Deflection  Elasticity modulus  To find out  Maximum…

Q: onsider a beam with a cross-section shown below for the question. The x and y axes pass through the…

A: Since the section is symmetrical about X-axis we get centroidal X-axis at half the section. Moment…

Q: (MPa), 022=b+c+d+h (MPa), t12=c+g+h+d (MPa), O°=2(T1), E= 1000(T1) Mpa, v=(T1)/100 a) Calculate…

A:

Q: A rigid horizontal slab is attached to two identical copper rods. There is a gap, A = 0.18 mm…

A: Given data,

Q: Please answer the ELONGATION OF BAR A IN mm and AXIAL STRESS DEVELOPE IN C IN MPa. Rate will be…

A:

Q: As shown in the figure, the simply supported beam is only subject to the action of dead weight, the…

A:

Q: A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the…

A:

Q: 125 mm 100 mm Y=si.15 mm 50 mm h - re 25 mm 25 mm

A: Given data: Taking top width as 100 mm then only y=81.25 mm. M=11.3 KN-m

Q: PROBLEM SOLVING : For final answers, use MPa for stress, kN for Force, and mm for…

A:

Q: A steel rod 3 ft long with a cross – sectional area of 1/576 ft² is stretched between two fixed…

A: L=3 ft A=0.25 in2

Q: Take XX=200 KN

A: Given data : Compressive load (P)=200 KNCross sectional area (A)=100×100 mInitial length (L)=1.70…

Q: The state of stress at a point is shown with respect to the xy-axes. Determine the equivalent state…

A: step 1-

Q: Q4) ( ): A state of stress is specified as shown in Figure (4), By using Mohr's circle determine the…

A: .

Q: 90°–0 9. A A metal [E = 106 GPa; v = 0.31] bar of height h= 40 mm and thickness t = 8 mm is…

A:

Q: Current Attempt in Progress Mohr's circle is shown for a point in a physical object that is…

A: Given: Consider the Mohr's circle given. Each grid square = 140 psi

Q: Problem 4- For the following cross section (all dimensions in mm) determine: a) The location and…

A: Calculating the location of neutral axis,

Q: Beams: 4a A beam of cross section as shown (dimensions in centimeters) is loaded by a positive…

A:

Q: Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses and…

A: Graphic representations of the transformation equations for plane stress problems are known as…

Q: A bar of length 1.70m has a square cross section of side 100 mm (as show. in the figure). The bar is…

A:

Q: Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal…

A:

Q: 10 mm 10 mm 8 kN -75 mm 75 mm 10 mm -70 mm -70 mm force of 8 kN, which is applied t cross-sectional…

A:

Q: The beam shown in the figure below is subject to a moment of M = 17 kN.m as illustrated. Calculate…

A: Given:-  M = 17 kNm

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A:

Q: 2.77 A steel rod 3 ft long with a cross-sectional area of 0.3 in.? is stretched between two fixed…

A:

Q: C Situation 7 - A rectangular bar 50 mm x 75 mm in cross-section is subjected to a tensile force P =…

A:

Q: A steel plate of width 120 mm and of thickness 20 mm is bent into a circular are of radius 10 m.…

A: Given:- The width of the steel plate = 120 mm  The thickness of the plate = 20 mm  The radius of the…

Q: The wide-flange beam is subjected to (Figure 1) Figure 200 m

A:

Q: The stresses shown act at a point on the free surface of a machine component. Normal and shear…

A:

Q: P+ D P

A: Given a single acting rivet connecting two steel plates having rivet diameter 22 mm, thickness of…

Q: Required information. Consider the given state of stress. Take X= 16 MPa and Y= 48 MPa. Y + X 60 MPa…

A:

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: (a) Stresses :σx=24 ksiσy=-72 ksiτxy=36 ksi

Q: For the beam shown below, b = 5 in and h = 12 in.  If the beam is subjected to a transverse shear…

A: Given: The value of b is 5 in. The value of h is 12 in. The transverse shear is 8 kip. Consider the…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, - 70 MPa and Sy =…

A: Given data in question  Normal stresses Shear stress = 0 Angle To find out  Normal and shear stress…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 70 MPa and Sy=…

A: Sx =70 MPaSy = -230 MPa.β = 52°

Q: A beam of rectangular cross-section 40 x 20 mm is loaded with tensile force 1000 N as shown in…

A: A rectangular cross-section beam 40 x 20 mm, Tensile load=1000 N.

Q: В 0.4h 0.2h 0.4h 0.4b 0.2b 0.4b

A: The given data is: Transverse Shear force (V) = 8 kip b = 6 in h = 14 in

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.