A beam of rectangular cross-section 40 x 20 mm is loaded with tensile force 1000 N as shown in figure. A Calculate the shear stress on oblique plane at 0 = 45° B0 B A 0.625 MPa D C 0.31 MPa 1.25 MPa

Q: A simply-supported beam of length 3L is. subjected to the loading shown in the figure. P L P L It is…

A:

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-sectic beam is…

A:

Q: A plastic beam of square cross section 30 mm × 30 mm (see figure) is simply supported with span…

A:

Q: The cross section of a beam shown carries a moment of -50 kN-m. Determine the following: (a) The…

A: First of all we have to find the neutral axis (N.A) of the given section. Then  we have to find the…

Q: Consider the nonprismatic cantilever beam of circular cross section shown. The beam has an internal…

A:

Q: A fiber tube with a regular polygon shape shown is 4.5 ft long, has a constant wall thickness of…

A: Thin tubular section: T=2T. tA t=thikness=0.05 in A=area of rectangle=2(1+(2)0.5)a2…

Q: The beam shown is subjected to two loads, one point and the other uniformly distributed. Determine…

A:

Q: A homogeneous bar AB as shown in Figure 3.3 -3 has a uniform cross - section and weighs 300 N/m. It…

A:

Q: Determine the stress in rod if tensile force applied of 35 N having cross sectional area of 50 mm2

A: Given  Tensile force F= 35 N Crossectional area A= 50 mm2

Q: The section of a thick beam has the dimensions shown in the figure below. Calculate the section…

A: Solution: Given: t=5mm d= 20 mm c = 10mm b=25 mm a = 15mm

Q: Problem 1. From the given beam and loading in the figure. a. Determine the neutral axis of the beam…

A:

Q: A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as…

A:

Q: A beam under load experiences sagging with a maximum bending moment of 24 x 106 Nm. The beam has a…

A: Calculate the maximum tensile stress and the maximum compressive stress for this beam.

Q: 1. A steel bar has a uniform cross sectional area of 300mm². Calculate the stress at member AB. 1.6m…

A: Given data,  Area = 300 mm²   To find out the stress at AB.

Q: An element in pure shear is subjected to stresses Tgy = 3,900 psi, as shown in the figure. Consider…

A:

Q: 3P A beam ABCD made of extruded aluminum and of length L = 1000 mm, is fixed at its ends A and D.…

A:

Q: A steel rod of length = 3m, diameter - 300 mm and modulus of elasticity = 200 GPa is inserted into…

A:

Q: section shown is 2.5 ft long and has a constant wall thickness of 0.080 in. Find (a) the largest…

A:

Q: Three bars AB, AC, and AD are pinned together as shown in the figure. Initially, the assembly is…

A: Assume L = 10ft cos35=10LAB; LAB=12.20ftcos20=10LAD;…

Q: To lower ends of the three bars in the figure two are the same level before the rigid homogeneous…

A: In the question given above, Total weight of the blockW =176 knThus , Ps +Ps+Pb=176 knAs the loading…

Q: 1. Determine the "t" parameter of cross section of the beam in the figure below se Navier formula)…

A: A structure is a structure or an assemblage of related elements that is used to aid a pile.…

Q: Using an Permissible stress of 155 MPa, determine the maximum bending moment M that can be applied…

A: Given,  An, I section beam, Allowable stress, σ = 155mpa Find out:- maximum bending moment,

Q: Q/1/ 9-13 . Determine the equivalent state of stress on an element if the element is oriented 60°…

A: The pressure that deforms the material in order to reduce the volume of the material is the…

Q: 2. The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the…

A: Given

Q: QUESTION 1: The frame shown in the figure is carrying a traingular distributed load. Pins at A and B…

A: Given :- A frame is carrying a triangular distributed load of w = 8 kN/m Allowable tensile stress of…

Q: Problem 3: The steel plate was originally in a rectangular shape. The 5 mm post-deformation geometry…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: normal strain in bar (2) is measured as –3,300 um/m. Use the dimensions L1 = 1,600 mm, L2 = 1,200…

A: According to given data The data given is question is different from the figure ,I am considering…

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 4.7 in., d = 4.1…

A: Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum…

Q: Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a…

A:

Q: Two wooden studs with cross-sectional dimensions 45×145 mm2 are glued together to form a beam with a…

A: To sketch the stress distribution, I will provide a graphical representation.

Q: Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a…

A: The expression of shear strain at point E is given as γx'y'=εx-εysin 2θ+γxy cos 2θ Substitute the…

Q: The AC beam given in the figure is subjected to a vertical force of 3 kN. Pull on AB bar the…

A: Stress=Load Area,        Load=A×6TAB=AREAAB×STRESSABTAB=AAB×SABTAB=π4d2×6AB…

Q: 1. Determine the "t" parameter of cross section of the beam in the figure below (use Navier formula)…

A: A structure is a structure or an assemblage of related elements that is used to aid a pile.…

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.