A beam shown on the figure is subjected to a uniform load of 5 kN/m. Determine the minimum shearing stress in MPa. The "x" distance on the beam makes the shear stress as small as possible. W=5 kN/m -4m- -50

Q: The cast iron beam in the figure has an overhang of length b = 2 m at each end. The bending working…

A: Assumption: Material is isotropic, homogeneous, and elastic in which hooks law is valid.  The plane…

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-sectic beam is…

A:

Q: A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has…

A: Given: Length, L = 300 mm Force, F = 414 N Modulus of Elasticity, E = 2 x 105 N/mm2 Moment of…

Q: The force p is applied at d=50 mm from the bottom as shown in the figure. Compute the normal stress…

A:

Q: QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum…

A: Solm ⇒ * Nevtral axis orientation* A1=10×40 ⇒ 400 mm2 , x1=402 ⇒ 2c mm, y1 = 5 mm  A2 = 50×10 ⇒ 500…

Q: 90 MPa 1. If a point is subjected to the state of stress shown in the figure, determine the…

A:

Q: 16 kN 60 12 70 Ölçüler mm cinsindendir.

A: Finding out stress at point A.

Q: Problem 1. From the given beam and loading in the figure. a. Determine the neutral axis of the beam…

A:

Q: Problem 2: A rigid block of negligible mass is supported by three symmetrically spaced rods as…

A: The stress in the copper bar is σc=70 MPa. The stress in the steel bar is σs=140 MPa. The area of…

Q: calculate A. The resultant force at joint C in KN B. The resultant force at joint A C. The stress at…

A: Answer  A. Calculation of resultant force at C We are given resultant force F = 190 KN due to…

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A:

Q: 10 k Sectian 300 800 ISM P= 300 ku, e = 250mn From the given figure shown, Calculate the stress at…

A:

Q: Example 7-5: The state of plane stress at a point with respect to the xy- axes is shown in the…

A:

Q: The differential element above represents the state of plane stress at a pont J steel beam. Which of…

A: Given data: σX=60 ksiσY=-20 ksiζXY=40 ksi

Q: Q1/ A beam has cross section as shown, it is subjected to a shear force of V 200 kN and a bending…

A:

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 5.3 in., d = 4.5…

A: Given: The value of a is 4 in. The value of b is 5.3 in. The value of d is 4.5 in. The value of t is…

Q: The piece of plastic is originally rectangular. Suppose that a = 300 mm and b = 450 mm.  A)…

A:

Q: 3. The shaft in the figure below consists of 75 mm diameter bronze segment that is rigidly joint to…

A: Solution:- We know that, torsion equation is TJ=τr=GθL by using this relation, the stress in AB…

Q: A square cross-section cantilever beam is subjected to a force as shown below. What is the maximum…

A: Given :

Q: The simply supported beam is subjected to the loadings shown in Figure Q2. Determine the value of P…

A:

Q: For the bar shown, calculate: 50 kN Ø40 mm a) The axial stress and strain due to uniaxial loading b)…

A: Given data : Tensile load (P)=50 KNDiameter (ϕ)=40 mmLength (L)=2 mPoisson ratio ν=0.3Modulus of…

Q: A beam of rectangular cross-section 40 x 20 mm is loaded with tensile force 1000 N as shown in…

A: A rectangular cross-section beam 40 x 20 mm, Tensile load=1000 N.

Q: The state of stress at a point is shown on the element. Enter your answers numerically separated by…

A: Consider the figure.

Q: Q.3) The Figure shown a beam with all dimensions. (a) Determine the bending stress at point H. 180…

A: Data given: Asked: Bending stress at point H. If the bending stress at point k is 9 MPa (T)…

Q: 1. Determine the "t" parameter of cross section of the beam in the figure below (use Navier formula)…

A: A structure is a structure or an assemblage of related elements that is used to aid a pile.…

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A:

Q: A cube of side 100 mm is subjected to an axial compressive load of 200 kN. Its lateral strain is…

A: A cube with a side of 100 mm is subjected to an axial compressive load of 200 kN.Lateral strain is…

Q: Q1/ A beam has cross section as shown, it is subjected to a shear force of V = 200 kN and a bending…

A:

Q: 1. For the beam showing in the figure, consider section n-n and determine; (a) The largest shearing…

A: It is required to find the maximum shear stress and shear stress at point a.

Q: The beam is subjected to a be 30

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.