A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: w (2) = - + F 48 %3D The value of E is 200,000 Nmm² and the values of ly is 20 x 10° mm“ The maximum value of z for the beam cross section is +20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm?

A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: w (2) = - + F 48 %3D The value of E is 200,000 Nmm² and the values of ly is 20 x 10° mm“ The maximum value of z for the beam cross section is +20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A circular steel tube of length L = 1.1 m is loaded in torsion by torques T (see figure). T L r2 (a) If the inner radius of the tube is r, = 49 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y, (in radians) at the inner surface? (Enter the magnitude.) rad (b) If the maximum allowable shear strain is 0.00041 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius (r,)max (in mm)? mm
85 In a pure shear condition, the maximum value of shear stress is observed to be 20 MPa for an element shown, subjected to above condition. The change in length of diagonal AB is μm. [Take G = 80 GPa] [Correct upto 2 decimal places] D 10 cm A 10 cm B () C
An element in pure shear is subjected to stresses Tgy = 3,900 psi, as shown in the figure. Consider only the in-plane stresses (the stresses in the xy plane). 4 Txy Using Mohr's circle, determine: (a) The stresses acting on an element oriented at a slope of 3 on 4 (see the figure) (Round your answers to nearest whole). psi psi psi Oz1 = Tzlyl Oyl %3D (b) The principal stresses. (Round your answers to nearest whole) Op1 %3D 01 = psi 02 = psi 3,
Mechanics of Deformable Bodies 80 N 200 mm 300 mm B The pipe shown in the figure has an inner diameter of 80 mm and an outer diameter of 100 mm. If its end is tightened against the support at A using a torque wrench at B, determine the shear stress developed in the material at the inner and outer walls along the central portion of the pipe when the 80-N forces are applied to the wrench. с 80 N
A square plate of side 300 mm is subjected to pure shear of intensity 100 MPa as shown in figure. Young's modulus of the material is 2 x 105 MPa and Poisson's ratio is 0.2. Find the algebraic sum of principal strains. 100 MPa B 100 MPa A D
Q2 B) The steel rod having a diameter of 2Z mm is subjected to an internal moment of 4Y0 Nm as shown in Figure Q2(b). Take: Z=0 Y =0 (i) Determine the stress created at points A, B, and C. Note that moments of inertia for the circular area can be determined by I= (ar' )/ 4. y A M= 4ΥΟ Nm 45° Radius = 0.5(2Z) mm Figure Q2(b) I= 7 (0.5× DD Q2 b (i ) x10-“m* 4 4 - Mc, MN /m² @ MPa (Compression) I MC MN / m² @ MPa (Tension) I - Mc, -400x 0.5(20) sin 45 = x10“ m* |MPa (Compression) I
Obtain the maximum bending moment Mx that the cross section given below can safely carry.The maximum normal stress is ? sefety = 100 ???.
Direct stresses of 120 N/mm2 (tension) and 90 N/mm2 (compression) are applied at a particular point in an elastic material on two mutually perpendicular planes. The principal stress in the material is limited to 200 N/mm2 (tension). Calculate the allowable value of shear stress at the point on the given planes. Determine also the value of the other principal stress and the maximum value of shear stress at the point using Mohr’s Circle.
The circular shaft AB consists of a 19 mm diameter solid steel cylinder in which a 5 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 59 Nm. What is the max shear stress in the shaft? Input your answer as a value only in MPa to one decimal place without +/- sign. L₁ L₂ C 150 Nm B
Derive a formula for the strain energy U of the cantilever bar shown in the figure. The bar has circular cross sections and length L. It is subjected to a distributed torque of intensity t per unit distance. The intensity varies linearly from t = 0 at the free end to a maximum value t = to at the support. Express your answer in terms of maximum value zo , length L, shear modulus G and polar moment of inertia Ip . U =
The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of materials with elastic-perfectly plastic behaviour. The yield stress of the material used for the channel shape cross-section is y=405 MPa, whereas that used for the rectangular cross- section is 0.850y. Compute the thickness of the web, t, of the channel shape section if the two cross sections have identical plastic bending moment about the z-axis. In Figure 4, h= 74 mm, b=52 mm, a-8 mm, H=74 mm, d= 52 mm Z b h Figure Q4 Z d H
Note: Read the question carefully and give me right solutions according to the question. Don't miss anything.