B) The steel rod having a diameter of 2Z mm is subjected to an internal moment of 4Y0 Nm as shown in Figure Q2(b). Take: Z=0 Y =0 (i) Determine the stress created at points A, B, and C. Note that moments of inertia for the circular area can be determined by 1= (ar* )/ 4. M = 4Y0 Nm Radius = 0.5(2Z) mm Figure Q2(b) (0.5 × DD )' Q2 b (i ) x10-“ m* 4 4 - Mc MN /m* @MPa (Compression) I Mc MN /m² @ MPa (Tension) I -M -400x 0.5(20) sin 45 = x10 m |MPa (Compression)

B) The steel rod having a diameter of 2Z mm is subjected to an internal moment of 4Y0 Nm as shown in Figure Q2(b). Take: Z=0 Y =0 (i) Determine the stress created at points A, B, and C. Note that moments of inertia for the circular area can be determined by 1= (ar* )/ 4. M = 4Y0 Nm Radius = 0.5(2Z) mm Figure Q2(b) (0.5 × DD )' Q2 b (i ) x10-“ m* 4 4 - Mc MN /m* @MPa (Compression) I Mc MN /m² @ MPa (Tension) I -M -400x 0.5(20) sin 45 = x10 m |MPa (Compression)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the given element is oriented at an angle of 25° with the x-axis, calculate the stresses acting on the element.
Question 1 Find the state of of stress for the element in Figure Q1 inclined by 30° counter clockwise by using: a) Equation Method b) Mohr's Circle Method 60 MPa Txy = 20 MPa 90 MPa Figure Q1
1. The member is loaded as shown. The diameter of the member is 32 mm. 1) Calculate all internal loadings on the cross section through the point A. 2) Calculate the stress at point A due to each internal loading. 0.4 m A Rigid Wall 1000 N 300 Nm 2000 N
The biaxial stress system in an element is shown in the figure. Which of the following will give the normal stress in N/mm² in the plane BD making an angle of 45° with the plane BA? σ¸ = 40 N/mm² G₁ = 60 N/mm 111 = 40 N/mm B a. = 60 N/mm
Q.b.
Solve the problem below and show your complete, systematic and neat solution with explanation.
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.19 in. In segment (2), the normal strain is measured as 1,650 pin./in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. Answers: (a) 8₂ = (b) E₁ = 41 in. (2) 93 in. lin. uin./in. P
xy=53
Q3) the state of plane stress at a point is represented by the element shown below. Determine state of stress at the point on another element oriented 30° e from the position shown and show these stresses properly on the rotated element. counterClock Wise 50 MPa 80 MPa (a) 25 MPa
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
The plate has a thickness of 20 mm and the force P = 5 kN acts along the centerline of this thickness such that d = 150 mm. (Figure 1) Figure d‡ 200 mm a 1 of 1
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?