The structure shown below consists of a brass core inserted into a steel tube of cross section square. If a moment of 8 kN × m is applied at its end, determine the maximum bending stress in the bar. E (brass) = 100 GPa, E (steel) = 200 GPa.

The structure shown below consists of a brass core inserted into a steel tube of cross section square. If a moment of 8 kN × m is applied at its end, determine the maximum bending stress in the bar. E (brass) = 100 GPa, E (steel) = 200 GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Aluminum Steel L= 0.9 m A = 300 mm? E= 200 x 10° N/m? a = 11.7 µm/(m-°C) L= 1.2 m A = 1200 mm E= 70…

Q: The The nut on a bolt is tightened by applying a force of P = 50 lb to the end of a wrench at a…

A: Given Diameter of bolt , d = 0.375 in Force, P = 50 lb Distance, a = 4 in Required Maximum…

Q: 1. The thermal extension of any member depends on the expanslon coefficient of this member. 2. The…

A: We only provide solution to first three answers, kindly resubmit the remaining parts for required…

Q: The state of stress at a point is given by 0=x²y² + 30, 0₁y = x² + y² + 15. o = xy²2 + 30, T₁y =…

A: First we summarise the given data : To find : Determine the body force distribution at the point (…

Q: A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂…

A: G = 10.93 MPaP = 13 kN or 13000 N

Q: A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a…

Q: A homogeneous bar AB as shown in Figure 3.3 -3 has a uniform cross - section and weighs 300 N/m. It…

Q: The State of stress at a point is shown with respect to the x-y axis. Determine the equivalent state…

A: Given : Determine the equivalent state of stress with respect to x'-y' axis?

Q: For the truss shown in the following figure, the temperature of member BC is raised by 140 °C, and…

Q: 1. Given that the value of P on the figure below is equal to 15 kN which is applied to the…

A: To Determine Stress in each rod segment.

Q: At a temperature of 34°F, a 0.06 in. gap exists between the ends of the two bars shown. Bar (1) is…

Q: 2. The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the…

Q: normal force in bar (1).

A: ### Calculation of Normal forces in bar 1 of given arrange of rigid beam ABCD ###

Q: A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi;…

A: Given that :-For Bar 1 :For Bar 2 :Required that :-(a) The total deformation in the bar.(b) Total…

Q: At a temperature of 53°F, a 0.1 in. gap exists between the ends of the two bars shown. Bar (1) is an…

A: Asked: To determine the lowest temperature at which the shown two bars will come in contact.…

Q: A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as…

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are…

Q: In the figure below is a slim, high-strength steel rule (E = 30X106 psi) having thickness 0.175 in.…

A: A) Given data ; E = 30 X 106 psi Thickness = 0.175 inches Length is = 48 inches To Find : Determine…

Q: Obtain the maximum bending moment Mx that the cross section given below can safely carry. The…

A: Sigma=100MPa

Q: The initially square element of a material is deformed as shown. Determine the shear strain of the…

A: To find shear strain of element To find normal strain along AC,BD

Q: 8 ksi For the state of stress shown in the figure, determine normal and shearing stresses on the…

Q: B) The steel rod having a diameter of 2Z mm is subjected to an internal moment of 4Y0 Nm as shown in…

Q: 10 mm 100mm 10mm 20 mm 60 mm 20 mm

Q: Figure below shows the stresses on an element ABCD. Determine the sum of normal and tangential…

Q: For an element subjected to ox = 40 MPa (compressive), oy = 30 MPa (tensile) and txy = +20 MPa, the…

Q: What is the max shear stress in the shaft? Input your answer as a value only in MPa to one decimal…

Q: rigid support @ A A 400 N-m 850 N-m L=1.4 m 30 mm diameter L=2.4 m 50 mm diameter L=1.9 m 30 mm…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: σ=PA ----( 1 ) here σ is stress , A is cross sectional area and P is force applied Calculate σst…

Q: An element in plane stress is subjected to stresses o, = -52.7 MPa and Txy = 41 MPa (see figure). It…

A: The stress element is shown in the figure.

Q: FOR THE ELEMENT SHOWN, DETERMINE THE MAXIMUM NORMAL STRESS AND SHOW IT ON A PROPERLY ORIENTED…

A: Given figure shows a stress element and it is required to find the principle stresses and maximum…

Q: The nut on a bolt is tightened by applying a force of P = 50 lb to the end of a wrench at a distance…

Q: Determine the state of stress on the The state of stress at a critical section is shown in Fig.…

A: Given : This is a problem of solid mechanics where we have to find the state of stress on the…

Q: A circular steel tube of length L = 1.5 m is loaded in torsion by torques T (see figure). (a) If the…

A: INTRODUCTION: This is the case of circular section for twist to be applied which causes the shear…

Q: A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi;…

Q: The member is loaded as shown. The diameter of the member is 32 mm. 1) Calculate all internal…

Q: It is made of solid circular cross-section bars, whose geometry and loading condition are given in…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

The structure shown below consists of a brass core inserted into a steel tube of cross section
square. If a moment of 8 kN × m is applied at its end, determine the maximum bending stress in the
bar. E (brass) = 100 GPa, E (steel) = 200 GPa.

8 kN-m
-3 m-
20 mm
100 mm
20 mm
20 mm
-20 mm
100 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. 0.75 m 1.5 m A B Steel A = 250 mm? E = 200 GPa Aluminum L= 2 m A = 300 mm? E = 70 GPa D
The nut on a bolt is tightened by applying a force of P = 18 lb to the end of a wrench at a distance of a = 7.0 in. from the axis of the bolt. The body of the bolt has an outside diameter of d = 0.425 in. What is the maximum torsional shear stress in the body of the bolt? Answer: Tmax i a psi
Using the force (flexibility/compatibility) method, analyse the structure in the figure below: A B ΕΙ C
In the figure below is a slim, high-strength steel rule (E = 30X106 psi) having thickness 0.175 in. and length of 48 in. has a moment applied into a circular are subtending a central angle of 40 degrees. L = length Mo Determine the maximum bending stress (ksi). 76.4 21.3 15.3 38.2 Mo
In the metallic structure represented by the figure below, the load P is 1200No. What is the maximum bending moment in member BC?
At a temperature of 34°F, a 0.06 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a = 12.5 x 10-6/°F] and bar (2) is stainless steel [a = 7.3 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. (1) 33m B (2) Answer: Final temperature = 55 in. -0.06. gap °F.
Problem 3 For the compound beam shown in Figure 4, determine the reaction forces, calculate the stress in each member, and determine the deformation in each beam using the Direct Stiffness Method. 3 ft 2 ft 2 ft y 500 lb 300 ft-lb 1= 0.948 in ¹ E = 30 106 psi I = 0.198 in ¹ E = 30-106 psi
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a = 2.9 x 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 x 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 38 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft 5.16 kips 4.86 kips 2.48 kips 3.88 kips O 4.09 kips (1) B 3 ft P 8 ft 1.5 ft
9. The initially square element of a material is deformed as shown. Determine the shear strain of the element and the normal strains of the diagonals AC and BD. Undeformed Deformed A B D 2.0 mm 2.015 mm C 1.995 mm
Mechanics of deformable bodies -solve with complete solution
SOLVE
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.45 in.2. After load P is applied, the strain in bar (1) is found to be 850 μεμε. Assume L1=53 in., L2=79 in., a=34 in., b=33 in., and c=30 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.