Answered: 1- For the element shown below,…

1- For the element shown below, determine the following: a. Maximum and minimum principal stresses b. Normal and shear stresses on plane AB 121 Ib/ft? 39 Ib/ft? A 60° 72 Ib/ft 39 lb/ft?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q. No. 12: A roadway sign that weighs P, = 9 kN is supported by a structural pipe with an outside…

A: Normal stress is generally the load applied perpendicular to various points and parallel to an area.…

Q: Problem 2. Determine the minimum height h of the beam shown in the figure if the flexural stress is…

A: Flexural stress The tensile strength of concrete beams or slabs is measured in terms of flexural…

Q: Find the span of the beam for the given beam-loading condition. Details of loading and beam is shown…

Q: The steel beam has the cross section shown. The beam length is L = 6.7 m, and the cross-sectional…

A: L = 6.7 m d = 355 mm bf = 205 mm tf = 13 mm tw = 9 mm

Q: SITUATION 3: A steel pipe of 300-mm outer diameter and 15-mm thickness is used as a column to carry…

Q: 10. Calculate the normal stresses at points A, B, C and D (at section A'A') for the beam shown…

A: To find out the normal stress at point A, B, C and D.

Q: 50 cm-long circular rod has a diameter of 10 mm and is acted pon by a 20 kN load acting to its…

A: Length of rod = 50 cm Diameter of rod = 10 mm Load = 20 KN E = 200 Gpa

Q: 3. 20 Mpa 25 40MPA Determine the normal stress perpendicular to the plane shown and the shearlstress…

Q: Determine the maximum bending stress (in MPa, numerical value only) of the beam shown below with the…

Q: g stress (in MPa, numerical value only) of the beam shown below with the given cross section. For…

A: Maximum moment :Mmax=-F1a+b+F2bMmax=-1.231.2+2.2+6.392.2=9.876 kN-m

Q: A 200 mm 50 mm Fixed to ground B 200 mm 2000 KN X A block of rubber 50 mm thick is sandwiched…

A: Data given dimension of steel plate = (200×200) mm =…

Q: 3. A beam simply supported on a 12-m span carries a uniformly distributed load of 30 kN/m over the…

A: Given ; span = 12m UDL = 30kn/m

Q: Upvote will be given. Please write the solutions legibly. Solve in 2 decimal place 15 KN 20 KN/m 4m…

Q: 6.6 Basic force sensor. The ceiling of a large building is supported by 16 vertical steel tubes,…

A: Solution Inner diameter= 100 mm Outer diameter= 140 mm Young modulus= 200 GPa Gauge Factor= 2.2

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

100%

1- For the element shown below, determine the following:
a. Maximum and minimum principal stresses
b. Normal and shear stresses on plane AB
121 Ib/ft
39 Ib/ft?
A
60"
72 lb/ft?
39 lb/ft?
B.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question: Derive the formula for the shear stress of a beam with a rectangular cross section and a triangular cross section.
A beam with the cross-section shown is subjected to a vertical shear of 28 kN. Determine: (a) the largest shearing stress in that section. (b) the shearing stress at Point a. 65 mm 100 mm -210 mm 8 mm 200 mm 8 mm T max = T@a= kPa kPa
1. Determine the maximum tensile stress and maximum compressive stress due to the load acting on the simple beam shown in figure. Data are as follows: P= 6.2 kN, L= 3.2 m, d = 1.25 m, b = 80 mm, t = 25 mm, h = 120 mm, and hi = 90 mm.
QUESTION 1
1. Determine the maximum compressive and tensile stress in beam AB as shown in the figure and draw the stress distribution over the cross section at this location. 25 kN/m 5m 50 KN 5m 4 m 50 KN 150 500 450 150
A steel wire 10m long hanging vertically supports a tensile load of 2000N. Neglecting the weight of the wire, determine the requires diameter if the stress is not to exceed to 140Mpa and the total elongation must not exceed 5mm. Assume E= 200Gpa.
SHOW COMPLETE SOLUTION AND ANSWER IN 3 DECIMAL PLACES 2. A water tank 2 m in diameter and 5 m high is made from steel having a thickness of 10mm. A) Determine the circumferential stress when the tank is fully filled with water. B) Determine the longitudinal stress at the bottom of the tank when it is fully filled with water. C) If the tangential stress is limited to 3 MPa, what maximum height to which the tank maybe filled with water?
A square post with a tubular cross section is loaded as shown in the figure below. a) Determine the state of the stress at point A having sides parallel to x and y axes. b) Determine the principal planes and principal stresses at point A at the base of the post.
Question 2 A simply supported beam of a channel section (see Figure Q2) is loaded by a vertical point load P= 10 kN (acting upwards) at mid-span. The length of the beam is L=3 m, the overall width and height of the section are of the same value a 50 mm, and the thickness of all three parts of the section is t= 10 mm. Find the value and location of the maximum shear stress in the beam. Figure Q2
The steel beam has the cross section shown. The beam length is L = 5.6 m, and the cross-sectional dimensions are d = 335 mm, bf = 195 mm, tf = 12 mm, and tw = 10 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 165 MPa. Wo X Answer: Wo= 12 B 72 C kN/m
(a) Determine the magnitudes of the stresses (report positive numbers here) at H caused by the forces and moments of Parts 1 and 2. Answers: OHaxial i ! МРа, OHbend = 123.615 MPa, THshear MPа, THtorque MPa. 50.499
Please help me with this one.