10. Calculate the normal stresses at points A, B, C and D (at section A'A') for the beam shown below. Consider the beam as simply supported at the ends. Consider also the weight of the beam. Additional data: unit weight = 9 kN/m³. 89 mm 0.5 KN AB 45 mm 4 m Section A'A' 1.5 m 0.25 kN 0.5 kN 1.5 m 4 m

10. Calculate the normal stresses at points A, B, C and D (at section A'A') for the beam shown below. Consider the beam as simply supported at the ends. Consider also the weight of the beam. Additional data: unit weight = 9 kN/m³. 89 mm 0.5 KN AB 45 mm 4 m Section A'A' 1.5 m 0.25 kN 0.5 kN 1.5 m 4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If P= 8.571 kN, Determine the stress in member CEassuming that the area in steel is 24 mm2.Show FBD
Q: - Analysis the beam shown below by the method of consistent deformation. El = constant सहर * 20 kN/m 4m B 2m GRAN PRE 2m SESSION Toe
q=20kN/m 100mm 75mm b=200mm L=0.9m R=9kN R=9kN (a) Determine the maximum bending stress and shear stress on the same section. h/2=50mm Ans. omax= 33.6 N/mm² h/2=50mm Tmax= 3 N/mm2 b=25mm (b)
Link AB is to be made of a steel for which the normal stress is 253 MPa. Determine the cross-sectional area (in mm2) for AB if P = 30.6 kNand d = 0.35. Round off the final aswer to four decimal places. 003 ехam.png ... 8 kN/m 35 OE D d d d
For the below wooden beam, under the given loading and dimensions: ŢŢ 50 kN C 4m w = 10 kN/m B 150 mmm Calculate ans sketch the shear stress distribution of the section at the support 360 mmm
PLATE 1 & 2 ARC206 STRENGTH OF MATERIALS TRUSS ANALYSIS 400 KN 500 KN 3 H 500 KN G 6.0 m 1. Analyze the beam 2. Tabulate the result of every member. 500 KN יד F D 400 KN E 3. Use the symbol (T) for tension and (C) for compression designation FOR PLATE 1, USE THE METHOD OF JOINT FOR ANALYSIS FOR PLATE 2, USE THE MAXWELL DIAGRAM FOR ANALYSIS 1.5 m
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)
Bi
Determine the maximum tensile or compressive stresses in the beam due to bending. The section has a base b= 140 mm and h= 240 mm PLACE THE ENTIRE PROCEDURE
Urgent. P = 11 kN ω0 = 9 kN/m a = 1.3 m
An M pair of forces is applied to the beam of which cross-section is shown in a plane that makes an angle eyle with the vertical. Find the stress at point A.
with explaination thanks