Situation 34A 50 cm-long circular rod has a diameter of 10 mm and is actedupon by a 20 kN load acting to its centroid, E = 200 GPa, Determinethe following:a. Axial Stressb. Deformationc. Straind. If the axial stress is limited to 25 MPa, Determine the maximumload that the rod may carry.e. If the deformation is limited to 1 mm, Determine the maximumload that the rod may carry.

Length of rod = 50 cm Diameter of rod = 10 mm Load = 20 KN E = 200 Gpa

50 cm-long circular rod has a diameter of 10 mm and is acted pon by a 20 kN load acting to its centroid, E = 200 GPa, Determine he following: Axial Stress Deformation - Strain . If the axial stress is limited to 25 MPa, Determine the maximum ad that the rod may carry. If the deformation is limited to 1 mm, Determine the maximum bad that the rod may carry.

50 cm-long circular rod has a diameter of 10 mm and is acted pon by a 20 kN load acting to its centroid, E = 200 GPa, Determine he following: Axial Stress Deformation - Strain . If the axial stress is limited to 25 MPa, Determine the maximum ad that the rod may carry. If the deformation is limited to 1 mm, Determine the maximum bad that the rod may carry.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SIMPLE STRAIN
The compound shaft has a uniform cross-sectional area with the given length of each segment. Using the applied torque on the indicated position, determine the safe diameter of the shaft if the allow stress in each segment is shown and the free end angular deformation is limited to 2.8° Hint: 3 different diameters from stress analysis One answer of diameter from angular deformation. 90DN-m A Treactuon 75DN/m 1200N-m 3.4m 15m 2.3m Allow Torsional Segment Stress G 70 Gfa AB 89GPA BC 28GP. CD GOMPA 75 MPa 50 MPa'
Question # 4: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. ( 2 m a 0.5m 400 KN 100 mm 300 mm 100 mm Section a-a
Find the minimum principal stress for the stress case given in the figure.
Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa
thanks
The copper rod AB and steel rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T1 = 17°C, determine the average normal stress in each member when T2 = 47°C. Also, how far will the collar be displaced? The cross-sectional area of each member is 1130 mm?. %3D Сopper Steel Elastic Modulus (GPa) 120 200 Coefficient of thermal expansion (1/°C) 17x10-6 12x10-6 В 1 m 0.6 m-
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
3. The rigid bar ABC is pinned at B and attached to the two vertical rods. Initially, the bar is horizontal and the vertical rods are stress-free. Determine the stress in the steel rod if the temperature of the both rods is decreased by 30°C. Neglect the weight of bar ABC. Steel L=0.9 m A 300 mm E= 200 x 10 N/m' a= 11.7 um/(m C) Aluminum L=1.2 m A = 1200 mm E = 70 x 10 N/m a= 23 pum/(m "C) Answer: Ost B 0.6 m 1.2 m
(a) A steel structural member of length = 10 ft. is supported between two fixed supports so that it cannot expand. At 68°F, there is no stress in the member. (E = 30 x 106 psi and α = 6.5 x 10-6/°F) Calculate the stress (psi) in the member at 95°F. Stress (psi) = (b) If the same structural member is not supported between two fixed supports, calculate the total elongation of the member (in.) for the same temperature change. elongation (in.) =
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
Solve it