QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at jointD in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint C. The allowable shearstress and bearing stress are t-60 MPa and o=120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge C that carry safely by the givensystem.b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter issufficient for the given system.0.8mIm0.6m15 kNВBeam AD20mmStrut CB40mm 100mm 40mm50mm 100mmDetail of joint CDetail of joint A

JOINT "C" is in double shear while JOINT "A" is in single shear.

a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system.

a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Estimate the safe inclined lDad as shown in Fig. Ex. 10.3. The rivets are 22 mm D, eight in number…

Q: *A bracket is held in place using a circular pattern of 6 bolts as shown. The circular pattern…

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: LRFD It applies Ultimate factored loads to design. Evaluate forces and stress using yielded…

Q: W12 x 120 3". 2" 3 @ 3" 2" 0000 D=304 L=65 WT6 × 29 W18 x 106

Q: o normal temperatures but wet in-service conditions. Assume =0.95 and the geometry factor is CA=1.…

A: 1 Area of the plate Ag Ag = 4×10 = 40 in2for A36 grade steel fy =36000…

Q: Design a connection for the following conditions: • 2L 8x6xtension member • Dead load = 50 kips,…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: The billboard post support a 5KN dead load as shown. The cantilever beam and the brace is pinned…

A: Answer (a) Calculation of ultimate force the brace carries Since the connection is pinned let us…

Q: Problem 2: A existing (E) W18x40 is deflecting too much and you were asked to decrease the floor…

A: Given data,section (E)W18x 40space is limiteduse maximum 3" deep memberFindchoose the WT member to…

Q: Deteminet verical dplacement of piCme dww e Ca m gures and incude the prriate unita Enter poe v the…

A: Determination of vertical deflection at C ###

Q: Test#1 -zzen-zax AlpQLSdM75VMOVqbMa1WtS9n99RYc6PifeGUTpVBOluyMUUVYQgqqA/formResponse YouTube Replace…

A: Given that: A cantilever beam as shown:

Q: Practice 6.4.6 Determine the maximum load that this fixture can take if factor of safety is set to…

A: The free body diagram is shown below and the force in the member AB is calculated as,

Q: 13. Determine the design strength of the connection shown below. Only check for bolt shear, bearing…

A: Design strength : The lower value of a material's actual resistance obtained while considering the…

Q: A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of…

Q: Determine the design capacity using ASD and NSCP specifications for the connection shown. Use A36…

Q: The tension member is fastened togother using two bolts, one on each side of the member as shown.…

Q: W8 x 13 W8XI5 4m Pa

Q: A 0.6 inch plate is attached to a 1.25 inch base plate using a pattern of ½ in UNC cap screws. The…

A: Answer:- c) 1.00 inch Solution given below-

Q: A beamtocolumn connection is made with a structural tee as shown in Figure . Eight…

A: Solution; Determine the bearing and shear nominal strengths. For the strength in bearing, use a hole…

Q: Determine the resultant load on the most stressed bolt in the eccentrically loaded connections…

A: first find the moment M=Pewhere = p = acting loade=eccentricity of loadM=100×6M=600k-in now find…

Q: Water flows through the pipe section shown. At the inlet the water velocity is 3.7 m/s and the mass…

A: Figure is as shown in the question

Q: Design an American Standard Channel from the C10 series that can resist the loads shown. The channel…

A: Given data- Member - A36 Length - 17 ft. Design load - Pu = 190 kips. Fy = 36 ksi. Fu = 58 ksi

Q: 3- The details for a turned-bolted conneetion are given in the figure below. The angle steel section…

Q: Determine the resultant load on the most stressed bolt in the eccentrically loaded connections…

A: Consider the free body diagram;

Q: what is the bolt bearing capacity of beam flange of the flange connection in kips? (2 decimal…

A: A992: Fy = 50 ksi, Fu = 65 ksieffective bolt hole diameter = bolt hole + 1/16"bolt hole diameter =…

Q: Perform the following for the moment connection from a W18X46 to a W14 column below. Assume that the…

Q: Q1: for the system shown, compute the value and the type of developed stresses at the aluminum block…

A: Answer Let us first draw the free body diagram for the system Calculation of value and stress in…

Q: 5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt…

Q: Problem set 7 cont.. 175k < 175k [445 kN] d The bolted connection shown is to be used to transmit a…

Q: A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place,…

Q: Find the size and the number of bolts needed to fix the cover for a pressure vessel of 20 mm…

A: Given DataPressure Vessel Thickness =20 mminternal diameter=120 mminternal Pressure=16 MPaσc Cover…

Q: Compute the service load capacity P for the welded bracket of the accompanying figure. The load is…

A: Given that :-A figure with welded bracket is given with following specifications.Live load = 70…

Q: Determine the resultant load on the most stressed bolt in the eccentrically loaded connections…

A: direct load=P=60k applied moment=60*(12/12)=60K-ft bolt B is the stressed most

Q: etermine the net area An of a 1/4 in by 4 inches plate and the diameter of the bolt is 7/8 in.…

A: width of plate=4in thickness of plate=1/4in diameter of bolt=7/8 in to find net area of plate

Q: what is the flexural rupture capacity of the shear plate of the shear connection in kips?

A: A36: Fy = 36 ksi, Fu = 58 ksieffective bolt hole diameter = bolt hole diameter + 1/16"bolt diameter…

Q: If P- 15 kips, what is the minimum diameter of the bolt without exceeding a shearing stress of 17…

Q: If the 18 mm plate is connected to two cover plate of 10 mm on top and bottom, what is the capacity…

Q: The bracket connection shown in Figure must support an eccentric load consisting of 9 kips of dead…

A: An elastic analysis is performed by applying the design loads and required internal forces in the…

Q: The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for…

A: Area = Force/ Shear stress

Q: A bolted connection shown in figure A uses the friction type connection with 22mm diameter A 325…

Q: Estimate the safe inclined load as shown in Fig. Ex. 10.3. The rivets are 22 mm D, eight in number…

Q: What is the type ofsupport A 400 N/m 200 N/m 4m - 3m -

A: (c) Pin is the type of support A

Q: 20 kN 40 kN Draw SFD B.M.D lom lom 20 m 20m on sider reaction at t support B as redundant

A: Given data:

Q: Select the reinforcing needed for the short tied column shown for the following: Pn-2200 kN, e= 250…

A: Mainly column is used to transfer the load coming from the beam to give it to the substructure and…

Q: The effective throat thickness of a fillet weld not to be greater than.... a. 0.3t b. 0.6t C. t d.…

A: Throat is the part of weld which is assumed to be effective in transferring the stress. Throat is…

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the clamping force on the boards is 600 lb, determine the required magnitude of the couple forces that must be applied perpendicular to the lever AB of the clamp at A and B in order to loosen the screw. The single square threaded screw has a mean diameter of 2 in and a lead of 0.25 in. The coefficient of friction is 0.3.
Replace the force-couple system acting on the pipe with an equivalent force-couple system acting at point O.
CH2-Hetant pa-Aote Acrobet Pro titended Ee Vien Decumem Comments Forme Tacs adanced wedew Hep 2/86 If the resultant of the loads shown passes through point B, determine the equivalent force-couple system at O. 45 kN 54 kN 1.2 m 0.9 m 0.9 m M 18 kN ahid ham
Draw influece line for Rvd (Please focus on the solution process) P=1 Hinge P RvD اشا A - 4m a 13 C TMA4 72
m) what is the block shear rupture (L-shaped) capacity of flange plate of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
QUESTIONS. In a factory, while connecting bracket required for supporting gantry girder to the ISHB 400 column with a group of 10 black bolts arranged in the pattern shown in figure. Determining the size of bolts required and thickness of gusset plate. Consider single shear bolted connection. 370 mm ◄ O O Q ▸ 125mm = 150 kN ISHB 100 W = 35 kN e = 300 mm
Q.6: Design a welded connection required to transmit a dead load of 120kips and live load of 290kips, by using two channel section C10×30 having web thickness of 0.873 inches with a gusset plate of 0.5 inch. The type of electrodes to be used for building is E77x. All materials are made up of A325 steel.
1- The bolted type connection will be used to assemble the given steel members. Determine the safe load that a single turned bolt can carry. Consider only the effect of shear stresses. (St-37, H) t= 20 # ##* JL 90.90.9 40 50 315 9,96 t 9,04 t 9,40 t 9,70 t
Problem 5 Design an American Standard Channel from the C10 series that can resist the loads shown. The channel is 17 ft long and is connected to a gusset plate (not shown) using the bolted connection configuration shown in the figure. Use A36 Steel (Fy-36 ksi, Fu-58 ksi). Obtain U using the equation given in AISC manual. Use the LRFD method. HC 10" INN 3" 31"> 3½" C10 Series Pu = 190 kips 3/4" bolts Hint: Determine the gross area needed (Ag) assuming yielding controls the design. Using Ag go to the tables in the manual to select a C10 with an area> Ag. Then check that the selected section is adequate in rupture and block shear.
Determine the maximum service load P (ASD) that the connection can resist. Use 27 mm Ø A490-N bolts, and 10 mm A-36 plate and a load P with a slope 1H: 2V. Assume that edge distance and bolt spacing are not critical. ***Note: Lod P is acting at a slope of 1H: 2V
The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in the bolts must be limited to 27 ksi, determine the minimum bolt diameter that may be used for this connection. Cocoo Answer:dmin- P in.
3. For the hanger in question 2, consider that the tension member is a plate of grade 350W material connected to a gusset plate, as shown below. Determine the required thickness of the plate with a width of 150 mm considering 4 M24 centred bolts with a pitch distance of 65 mm and end distance of 45 mm. Assume that the holes are drilled. Activa Click M C