1.) Draw the Free-Body Diagram for each mechanism shown. Provide a direction a a name for each reaction force/moment. Only the minimum number of required reactions is required (none of the "optional / ambiguous reactions" need to be

Q: Can you write the solution in a sheet of paper? Thank you!

A: As asked, solution is provided on a paper.

Q: Calculate the error (mm) in the linear measurement of offset, if the length of the offset is 80 m,…

A: Given information,  Offset length = 80 m Accuracy in measurement in length= 1cm in 60m

Q: ) Consider the 2D beam supported by a roller at A and a pin at B. INTERNAL FORCES c) Draw the…

A:

Q: e and porosity.

A: Given e and porosity

Q: For the beams shown, draw the influence 1ines for the given functions. Use the beam sign convention…

A:

Q: 60 k. ft DETERMINE THE SHEAR AND AND MOMENT MOMENT FOR EVERY 8-FT STRIP INTERVAL STARTING AT POINT A…

A:

Q: Consider the beam shown in (Figure 1). The members are pin connected at E and F. Suppose that P =…

A: Using static equilibrium conditions, summation of moment at F = 0, ( Because, there are only…

Q: 2.3.2 If the beam section of Prob. 2.2.3 is reinforced with 3-25 mm diameter steel bars in the…

A: Given Data: fc = 30mpa 3-25 mm dia steel 65mm from the extreme fiber

Q: Define coefficient of volumetric expansion.

A: The coefficient of volumetric expansion is defined as the ratio change in volume with respect to the…

Q: A W30x90 A36 steel girder spans 12 m on simple supports. It carries a uniformly distributed load of…

A: a. To determine the required section modulus, we need to calculate the maximum bending moment the…

Q: Determine the moment about point O in terms of N-m. – 4 ft- 3 ft 45°. |-1 ft-| 50 N

A: The FBD of the section is shown below:

Q: Complete the chemical reaction below. ? °C CaCO3 CaO CO2

A: Given chemical reaction is, CaCO3→? °CCaO+CO2   The standard Gibbs free energy of reaction is…

Q: List 15 types of construction materials

A: Following are the types of construction materials

Q: How did you derive the formula?

A: Given: h1= 200 mm   h2 =80 mm   k1=0.004 cm/sec,   H1 = 100 mm   H2 = 150 mm. Required: To explain…

Q: The mass of body A is 45 kg. The coefficient of friction for bodies A, B, and the ramp C is 0.10.…

A:

Q: Determine the force in each member. State if the members are in tension or compression. Assume the…

A:

Q: Determine the right triangle side lengths, whose one angle is 45 degrees, and the hypotenuse is 5 √2…

A: The values and diagram given in the question are as follows: one angle of the right-angle triangle…

Q: The car travels around the portion of a circular track having a radius of r = 500 ft such that when…

A:

Q: What are the applications in actual practice of ASTM (American Society for Testing and Materials)

A: American Society for Testing and Materials: The American Society for Testing and Materials (ASTM) is…

Q: 5. Calculate the minimum passing sight distance required for a two-lane rural roadway that has a…

A: The formula of minimum passing sight distance is given by,

Q: a Find the distance x between the points (1,4) and (5, –8).

A: Distance X between two points is calculated as follow

Q: 2) An 8m steel tape was purchased and advertised as follows: Standard temperature Standard Pull Таре…

A:

Q: Use the virtual work method to find: a. slope at A b. slope at B c. deflection at the midpoint of…

A: Using Virtual work method##  calculation of slope at A and B and deflection at  mid span of beam

Q: 300 lb 2' 200 lb -ペー ー -2- -2-

A:

Q: For a moist soil sample, the following are given. • Total volume: V=1.2 m3 • Total mass: M=2350 kg •…

A:

Q: P,= 500 k J. P, = 1,000 k I P,= 500 k %3D %3D Py= 1,000 k fixed fixed Check whether a 17 ft W 14 x…

A: In construction, steel is one of the most commonly used materials. The material is widely used from…

Q: Please provide a complete solution in a sheet of paper.

A:

Q:  please provide me with the step-by-step solution

A: Given: SystemDollar (Cost)TonMinuteDollar per ton per…

Q: = What is the gage pressure [in psi]... Water Air Oil (SG=0.8)

A: Given:Required:Gage pressure at bottom of tankGage pressure in the air zone in the container

Q: 0.7 m 1.6 m 800 N 1m BRUOR 200 N 0.7 m To bool -1.5 m-

A:

Q: STATICS OF RIGID BODIES Three wheel loads rail as a unit across a 12m span. The loads are A-10kn,…

A: The figure is as shown below

Q: 9.3-23 The beam shown in the figure has a sliding support at A and a roller support at B. The…

A: Draw FBD:Calculate Bending moment equation:

Q: Determine the factor of safety of the slope shown in the figure below using an ESA and a TSA. The…

A:

Q: A two-membered frame is joined by a pin at B, D, and E. Determine the horizontal and vertical…

A:

Q: 12. The uniform bar and the homogeneous cylinder eac equilibrium, calculate the normal and friction…

A:

Q: Problem 1 Determine the magnitude of the moment about point A and its direction at the plane having…

A:

Q: An elementary triangular concrete gravity dam, supporting 60 m height of reservoir water, should…

A: Given data- Elementary triangular concrete gravity dam- height H=60 m, Full uplift case, To Find-…

Q: shown below, water flows from A to junction J at a flow rate Q1 = 0.70 m³/sec. The reservoir/Node…

A: Elevation of reservoir A, Elevation of Node J, Diameter of pipe 1, Hazen's Williams Constant,…

Q: allowed.

A: Given data- Diameter of the solid segment 1 d1 = 41 mm= 0.041mDiameter of the solid segment 2 d2 =…

Q: A boat is towed at the rate of 12mi/hr. At t=0, the towing line is cast offand a man in the boat…

A: A boat is being towed at the rate of 12 mi/hr. At the instant (t = 0) that the towing line is cast…

Q: Based on the survey notes below, fill in the necessary data to answer the next set of questions. All…

A: Reduced level :- Elevation of a point with respect to mean sea level is called Reduced Level.Back…

Q: A tray has 7 yellow plates, 14 white plates and 16 gray plates. In how many ways can a person make a…

A: The values given in the question are as follows: Number of yellow plates=7 Number of white plates=14…

Q: How is plastic made

A: