Water flows through the pipe section shown. At the inlet the water velocity is 3.7 m/s and the mass flow rate is 17 kg/s. At the outlet the water velocity is 7.3 m/s. Determine the total nett force (Fbolts shown) exerted on the bolts holding the pipe together (not the force of each individual bolt). Provide answers to 1 decimal place and Sl units are required Inlet diameter D System - fluid flow through bolt-connected pipe Outlet diameter d Fluid in Fluid out BACK VIEW FRONT VIEW SIDE VIEW Free body diagram F holts Min' Mout

Water flows through the pipe section shown. At the inlet the water velocity is 3.7 m/s and the mass flow rate is 17 kg/s. At the outlet the water velocity is 7.3 m/s. Determine the total nett force (Fbolts shown) exerted on the bolts holding the pipe together (not the force of each individual bolt). Provide answers to 1 decimal place and Sl units are required Inlet diameter D System - fluid flow through bolt-connected pipe Outlet diameter d Fluid in Fluid out BACK VIEW FRONT VIEW SIDE VIEW Free body diagram F holts Min' Mout

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

There is a square gate with the dimensions showed in the figure 1. This gate is hinged the upper edge. Calculate the minimum required moment applying to the hinge to open the gate. Water 12' 6' 10' Water -Hinge -Sill the gate
QUESTIONS. In a factory, while connecting bracket required for supporting gantry girder to the ISHB 400 column with a group of 10 black bolts arranged in the pattern shown in figure. Determining the size of bolts required and thickness of gusset plate. Consider single shear bolted connection. 370 mm ◄ O O Q ▸ 125mm = 150 kN ISHB 100 W = 35 kN e = 300 mm
Draw simple FBD and submit the solution within 25 minutes, Urgent.
7. Please show your complete solution. Please typewritten for upvote.
The gate shown is hinged through a point A and is restrained from opening by a fixed ridge at point B. For a gate width of 2 meters, •Determine the magnitude and direction of the force exerted on the plate by the ridge. Illustrate and label the FBD of the force system. Express your answer in kN. DRAW FBD. NEED IT ASAP!
Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter. The connection is bottled at the web only. Assume x= 0.76 inch. 1. The gross and net areas Ag and An.
Q1. it's required to determine the diameter of pipe BC
figure below. The specific of oil is 0.8. (H₁-3m, H₂-2.6m, H3-4m, P-49.05 kPa, L=5m) 2.8. Calculate the force F necessary to hold the 4 m-wide gate AB in position shown in the A 2 hinge triangles lix5x48-4080 13 Air Oil Water H₁) H₂ H3) P 8₁ 40+ +/215 1197
A0.375-in.-diameter steel [E = 30,000 ksi] bolt (1) is placed in a copper tube (2), as shown. The copper [E = 16,000 ksi] tube has an outside diameter of 1.000 in., a wall thickness of 0.12 in., and a length of L= 7.0 in. Rigid washers, each with a thickness of t= 0.125 in., cap the ends of the copper tube. The bolt has 24 threads per inch. This means that each time the nut is turned one complete revolution, the nut advances 1/24 in. The nut is hand-tightened on the bolt until the bolt, nut, washers, and tube are just snug, meaning that all slack has been removed from the assembly, but no stress has yet been induced. What stresses are produced in the bolt and in the tube if the nut is tightened an additional quarter turn past the snug-tight condition? Rigid washer Rigid washer Bolt () Tube (2) If the force induced in the bolt by advancing the nut is F1, and force induced in the tube by advancing the nut is F2, what is the relationship between F1 and F2?
DETERMINE THE PROPER POSITION OF THE C-PURLIN IF THE LOAD IS SUBJECTED DOWNWARD. 1. DETERMINE THE MOMENT OF INERTIA WITH RESPECT TO ITS CENTROIDAL X-AXIS (Uit: mm^4) 2. DETERMINE THE MOMENT OF INERTIA WITH RESPECT TO ITS CENTROIDAL Y-AXIS (Unit: mm^4) 3. PROPER POSITION OF THE PURLIN (A or B) (A) (B) 10 mm I80 mm 100 mm 10 mm 10 mm 100 ma 10 mm 180 mm 001
.