For the hanger in question 2, consider that the tension member is a plate of grade 350W material connected to a gusset plate, as shown below. Determine the required thickness of the plate with a width of 150 mm considering 4 M24 centred bolts with a pitch distance of 65 mm and end distance of 45 mm. Assume that the holes are drilled.

For the hanger in question 2, consider that the tension member is a plate of grade 350W material connected to a gusset plate, as shown below. Determine the required thickness of the plate with a width of 150 mm considering 4 M24 centred bolts with a pitch distance of 65 mm and end distance of 45 mm. Assume that the holes are drilled.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Shown in Figure 1 is a centrically loaded bolted connection. The diameter of the bolts is 19 mm while holes have 21 mm diameter. Use depth 4y = 200 mm. 1. Determine the critical net width (Net Width) for the staggered bolted connection as shown in the figure. 2. Determine the value of "x" so that the net width along bolts A-B-C-D-E is equal to the net width along bolts A-B-D-E.
Please answer all the questions with a complete solution. thank you.
Please answer this po, thank you so much!
For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter. Plate 1/2" x 11" .T 7/8" dia. bolt, typ. ASTM A325N
A double cover butt joint is shown in figure 2 below. If the steel is Grade S355JR and the bolts are M20 Grade 8.8 S, determine the strength of the connection. Assume the contact surface of the bolts are blast – cleaned with Class B coatings. The connection is required not to slip at serviceability. 80 120 80 80 120 80 -13 All dimensions are in mm Figure 2: Double cover butt joint. 300 O O O O o o O o o
A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use NSCP specifications and assume a double row of bolts with standardsize holes for a bearing type connection with threads excluded from the shear planes.Minimum tensile strength Fu = 552.93MPa. Assume diameter hole is 3mm bigger than thediameter of bolts. Allowable shear stress is Fv = 207MPa. Allowable bearing stress fb = 1.2Fu.Diameter of bolts is 19mm. Fy = 449.25MPa.(a) Compute the tensile capacity of the steel plates. (Max. Net Area = 0.85 of Gross Area)(b) Compute the number of 19mm diameter bolts to develop the full strength of the plates. Note: SHOW DRAWINGS AND SOLUTIONS.
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
Calculate the maximum tensile load, Ta or Tu of the connection shown in Figure 7. Theconnection consists of two 3/8" plates fastened to each side of one 13/16" plate.Assume 7/8" diameter bolts and standard punched holes. Use A36 steel. The plate is 13” wide. Note: Be sure to check all failure modes; bolt failure modes, and member failure modes(including block shear)
Don't copy from other experts solution.
Show 5 failures. Show step by step solution. Steel Type: Cross section flat bar PL 12.7 x 165 with an area of 2095.5 mm2 Textbook reference Handbook of steel construction.
The block shear strength of the tension member as shown in figure is (round off to two decimal places). Assume grade of plate Fe410. 45 mm 35 mm 50 mm 100 mm ISA 80 x 50 x 8 mm (M20 bolt of grade 4.6 is used) KN