Answered: For the cross section shown, calculate…

For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two rods are connected to each other and are restrained at top and bottom. The top portion is steel…

Q: hexagonnal head 60 mm threads bolt diameter @ threads 32 mm bolt diameter - 38 mm T=80 kN Calculate…

A: We have to determine the value of tensile stress in the body of the bolt and tensile stress at the…

Q: Calculate the percentage of steel from the figure shown below? 400 mm 8 Y 20 400 mm All dimensions…

A: Given Square RCC section 400*400 mm Reinforcement = 8# 20 mm dia bars. To Determine percentage of…

Q: 35. What grade of steel is most commonly used today in the production of W-shapes, and what are its…

Q: A cylindrical rod is designed of A36 steel (Ftall=Allowable tensile stress=24ksi). What is the…

A: To Determine Smallest reasonable sized rod that could support the 15,000 pounds, R

Q: 2. The tensile link shown is flat, is 5 mm. thick, and carries an axial loac a. Compute the maximum…

A: GIVEN- Axial load (P)=1350 N Thicknesss (t)= 5 mm

Q: A composite column member is fabricated on top of a base plate as shown in the figure. What should…

Q: hected on both legs with 12 mm diameter bolts. Given that s = 50 mm

A: consider figure for solution

Q: 38. What grade of steel is preferred for the fabrication of most structural shapes other than…

A: Given data : Structural shapes Find : Grade of steel and its yield and tensile stress Shapes like W…

Q: A steel bar of length 30 m and having specific weight of 20 x 10-5 N/mm³. Find the elongation of the…

Q: Sample: Malleable Steel (AISI 4145) Original Diameter: 6.14mm Gauge Length: 55 mm Final Length:…

A: Given data, Original diameter D = 6.14 mm Gauge length L = 55 mm

Q: Calculate Poisson's Ratio for a steel that has a modulus of elasticity E of 30,000,000 psi and a…

A: The given data is: Modulus of elasticity, E=30000000 psi Modulus of rigidity, G=11500000 psi

Q: Two plates are connected by fillet welds of size 10 mm and subjected to tension, as shown in the…

A: Given:Load carried by both the weldsLoad carried by each weld.Constant that depends upon the angle…

Q: Situation 4: For the given section shown in the figure, determine the following: 20 mm 120 mm 20 mm…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: From the given figure below, determine the a. centroidal moment of inertia Igx and Igy b. section…

Q: tress in segment bronze and steel

A: Given data : Area for bronze segment (ABr)=700 mm2Area for steel segment (ASt)=800 mm2Force in…

Q: Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. USE…

Q: A2m rigid bar is carried by three rods as shown. The mechanism is arranged such that it is…

A: Calculate length of steel rod,Lst=?

Q: Each of the three aluminum bars shown is to be twisted through an angle of 2.5°. Knowing that b=30…

A: Given, Allowable shear stress, τall = 50 MPa b = 30 mm Modulus of rigidity (G) = 27 GPa or 27000…

Q: A No. 8 steel rebar is tested in tension. By monitoring the load reading of the testing machine, it…

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and…

Q: Two plates are proposed to be jointed by welding as shown in the figure. Determine the size and…

Q: steel bar originally 200 mm long is pulled in tension with stress 150 MPa the magnitude of elastic…

Q: Determine the maximum tensile strength of the steel bar described by the following data Initial…

Q: 8. If the modular ratio is equal to 11, and the Modulus of Elasticity of the Steel is 200,000 MPa.…

A: GIVEN Modular ratio, m = 11 Modulus of elasticity of steel, Es = 200,000 MPa To Determine Value of…

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and…

Q: An ASTM A615 grade 60 number 10 rebar with a gauge length of 8 in. was subjected to tension to…

A: It is required to determine the stress in the rebar. Here, P is the load and A is the area of the…

Q: For the built-up shape shown, determine: A) the elastic section modulus and the yield moment (b)…

A: Given:Required:(a) the elastic section modulus and the yield moment (b) the plastic section modulus…

Q: s used as a tension member connected on both legs with 20 mm diameter bolts. Given that s = 50 mm,…

A: Given:- 20 mm diameter bolts s = 50 mm t=8mm Ag=1852mm2 To find:- Design strength

Q: À steel beam is welded according to the figure below with two welds. The beam is loaded with a force…

A: (a) For 20mm thick member a (minimum size of weld) = 5mm

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and…

Q: DISCUSS THE STRESS-STRAIN RELATIONSHIP SHOWN BELOW (WRITE IN ENGINEERING LETTERING) Actual Rupture…

Q: s used as a tension member connected on both legs with 22 mm diameter bolts. Given that s = 50 mm,…

A: Given:- Ag = 1,852 mm2 t = 8 mm s = 50 mm, 22 mm diameter bolts To find:- Design strength (kN)

Q: A combined section of steel and copper is subjected to a compressive load. Refer to the table below…

A: We will calculate stress using maximum strain.

Q: 2-6 A specimen of steel having an initial diameter of 0.503 in was tested in tension using a gauge…

A: Given, D = 0.503 in L = 2 in

Q: What will be the tensile strength due to rupture of critical section of an angle section ISA 150 x…

Concept explainers

Pressure and Stress

Question

For the cross section shown, calculate the tensile capacity of the steel plate. Assume
that the bolt hole is 1/16 inch larger than bolt diameter.
Plate 1/2" x 11"
.T
7/8" dia. bolt, typ.
ASTM A325N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design rod to support load of 175,000 pounds. What diameter rod is appropriate? Safety Factor, SF= Strength of Material (S)/ Applied Stress (sigma) = 1 Applied stress (sigma) = Force/Area Yield strength of Steel = 100,000 psi (yield means will undergo plastic deformation)
Need answer!
Discuss the following in the design of structural steel i) Bars and rods ii) Plates and flat bars
A fillet-welded joint is shown in the figure. The size of the weld is 8 mm. Safe stress in the weld is 110 N/mm². What is the safe force (to the nearest magnitude) to which the weld can be subjected? -80mm- 60 mm
PLEASE WRITE YOUR COMPLETE SOLUTION AND BOX THE FINAL ANSWER. THANK YOU. A series of rigidly attached aluminum bars carries the axial loads at the positions shown. If the modulus of elasticity E = 16×10^6 psi, compute the total deformation of the bar and state if the bar elongates or shortens. Assume that the bar is suitably braced to prevent lateral buckling.
A fillet-welded joint is shown in the figure. The size of the weld is 8 mm. Safe stress in the weld is 110 N/mm². What is the safe force (to the nearest magnitude) to which the weld can be subjected? 80 mm 60 mm
An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
At a temperature of 29.8 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 133.3°C, determine the change in length of the steel rod if L = 312.45 mm and M=201 mm. Round off the final answer to four decimal places. d - L M - B Aluminum A = 2000 mm² E = 75 GPa a = 23 x 10-6/°C Stainless steel A = 800 mm² E = 190 GPa α = 17.3 x 10-6/°C
Please show solutions on how to get the 0.75 value. The circle green in the figure. Civil engineering- steel design
An A36 angle bar is used as a tension member connected on both legs with 12 mm diameter bolts. Given that s = 50 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm
1
Please show complete solution and explanation thank you