(5) If 200 g of polymer A, 300 g of polymer B, 500 g polymer C, and 100 g of polymer D are mixed, calculate both M, and Mw of the blend? Polymer A M, = 45,000; Polymer B Polymer C M, = 80,000; Mw = 85,000 Polymer D M, = 300,000; Mw = 900,000 What are the polydispersity index and the standard deviation of the number distribution of molecular weight of the mixture? Mw = 65,000 Mn = 100,000; Mw = 200,000 %3D

(5) If 200 g of polymer A, 300 g of polymer B, 500 g polymer C, and 100 g of polymer D are mixed, calculate both M, and Mw of the blend? Polymer A M, = 45,000; Polymer B Polymer C M, = 80,000; Mw = 85,000 Polymer D M, = 300,000; Mw = 900,000 What are the polydispersity index and the standard deviation of the number distribution of molecular weight of the mixture? Mw = 65,000 Mn = 100,000; Mw = 200,000 %3D

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

The following data was obtained when four bottles of wine, were analyzed for residual sugar content and the results obtained are the followingB Bottles % w/v Residual Sugar 1 0.97, 0.86, 1.02 2 1.25, 1.32, 1.13, 1.20, 1.12 3 0.9, 0.92, 0.73 0.72, 0.77, 0.61,0.58 a) For each set, determine the mean, spread, standard deviation s and coefficient of variation. b) Calculate the pooled standard deviation, spooled. 2.
P:13)
6
3. (a) The following are the results from subjecting the lectin to SDS-PAGE: Band / Molecular Length 210 100 67 48 32 Lectin Weight (kDa) of Gel Migration Distance 7.2 1.8 2.5 3.2 3.9 4.7 3.5 (cm) Determine the molecular weight of the lectin. Show all workings.
Only typed solution.
Bradford assay was used to determine bovine serum albumin (BSA) concentrations. The method works by binding Coomassie Brilliant Blue dye to protein standards and unknown, leading to a shift in the absorbance maximum of the dye. A stock solution of BSA is available (10 mg/ml) from which the protein standards were prepared. Bradford reagent, 290 ul, was pipetted into a transparent 96-well microplate. 10 ul of the protein dilution was added followed by mixing in the wells. After 5 min of incubation at room temperature, the plate was read in spectrum mode with the absorbance spectrometer of the microplate reader. The spectrum of the dye not bound to protein was also determined. Create a standard curve or regression equation that related the protein concentration and absorbance. An unknown BSA sample was prepared the same way as the standard and the OD was 0.35. determine the original concentration of the protein solution. The measurements can be seen below. 0.0625 Protein Concentration…
Q1. (a) In each of the following cases (I. to III.) identify which polymer in each pair has the greatest Tg and then explain your selection in terms of molecular structures. Assume that molecular weight differences are insignificant. Note: PMV = pendant molar volume/ cm³/mol Pair I Section A Answer ALL questions in this Section Pair II Pair III Polymer 1 H₂ +²2² 0+. Repeat unit A ht Polymer 3 (PMV=92.3) 3 Polymer 5 (PMV-60.1) tyt OC-CH₂ Polymer 2 | to-0²-0-0 H₂ + -ot Polymer 4 (143.9) (b) Consider the following repeat units A and B, state which polymer is likely to be amorphous and which is likely to be semi-crystalline then explain why in terms of the structure of the repeating units. to *** Polymer 6 (PMV=70.3) Repeat unit B t
Chemistry Calculate Mn Mw Mz n1 100 80 70 50 30 M1 50 40 30 20 10 Example 2. Calculate Mn, Mw for mixtures having one part of A and two part of B. Monodisperse Polymer A (molecular weight: 100,000) Monodisperse Polymer B (molecular weight: 400,000)
A silica TLC plate is developed in a mixture of solvent system/mobile phase. The solvent travels 30 mm up the plate Analyte #1 travels 9 mm up the plate Analyte #2 travels 16 mm up the plate Which analyte is more polar, and what is its Rf? Analyte #1, Rf = 0.53 Analyte #2, Rf = 0.53 Analyte #2, Rf = 0.3 Analyte #1, Rf = 0.3
6
What is quantitative transfer and why is it used?
An atomic absorption method for the determination of the amount of iron present in used jet engine oil was found from pooling 30 triplicate analyses to have a standard deviation s = 3.1 µg Fe/mL. If s is a good estimate of o, calculate the 95 and 99% confidence intervals for the result 21.7 µg Fe/mL if it was based on the following criteria. (a) a single analysis 95% confidence interval= 21.7 + 99% confidence interval = 21.7 + (b) the mean of two analyses 95% confidence interval = 21.7 + 99% confidence interval= (c) the mean of six analyses 21.7 ± 95% confidence interval = 21.7 + 99% confidence interval= 21.7 + μg Fe/mL μg Fe/mL μg Fe/mL μg Fe/mL μg Fe/mL μg Fe/mL