do fast For the figure below, determine the magnitude of thelinear velocity of joint C, in m/s:V₁ = 1.5 m/sVAaA = 0.5 m/s²90°0.5 mBA60°0.6 m

Answered: Image /qna-images/answer/53a4cfdd-2c93-417f-bbc9-d8cfdfbe7d5f.jpg

Answered: For the figure below, determine the…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter10: Introduction To Simulation Modeling

Section: Chapter Questions

Problem 41P: At the beginning of each week, a machine is in one of four conditions: 1 = excellent; 2 = good; 3 =...

See similar textbooks

Similar questions

A 50-mm-diameter, thin-walled metal pipe covered with a 25-mm-thick layer of insulation (0.085 W/mK) and carrying superheated steam at atmospheric pres- sure is suspended from the ceiling of a large room. The steam temperature entering the pipe is 120°C, and the air temperature is 20°C. The convection heat transfer coefficient on the outer surface of the covered pipe is 10 W/m² K. If the velocity of the steam is 10 m/s, at what point along the pipe will the steam begin condensing? i will 10 upvotes urgent
1m radius disk is moving on the inclined surface under no slip condition. the center of the disk has 3m/s velocity and according to the figure, bar BC is pinned to the disk at point C and point B always stays on the ground. 1) find angular velocity of BC. 2) find angular acceleration of BC
do fast.
Calculate the biaxial stresses σ₁ and σ₂ for the biaxial stress case, where ε₁= 0.002 and ε₂ = - 0.001 are determined experimentally on an aluminum member of elastic constants, E = 71 GPa and v = 0.35 . Also, determine the value for the maximum shear stress.
The 180-mm disk is at rest when it is placed in contact with a belt moving at a constant speed. Neglecting the weight of the link AB and knowing that the coefficient of kinetic friction between the disk and the belt is 0.44, determine the angular acceleration of the disk while slipping occurs. 180 mm K 60° B The angular acceleration of the disk is 63.1019 ✪ rad/s² 0.
A hair dryer is basically a duct of constant diameter in which a few layers of electric resistors are placed. A small fan pulls the air in and forces it through the resistors where it is heated. If the density of air is 1.20 kg/m³ at the inlet and 0.935 kg/m³ at the exit, determine the percent increase in the velocity of air as it flows through the dryer. p kg/m³ 1.20 kg/m³ The percent increase in the velocity of air is %.
The number of yearly breakdowns for the power generator observed over the past 20 years at Orlando Utilities is presented in the following data: Number of breakdowns 0 1 2 3 4 5 6 Number of years in which breakdowns occurred 2 2 5 4 5 2 0 For Orlando Utilities, the expected number of breakdowns = (round your response to two decimal places).
Water flows at 2 m/s through a 2.5 m length of a 25 mm inside diameter tube. The inlet temperature of water is 293 K and its outlet temperature is 295 K. Assume that the inside surface temperature of the tube is at 320 K. Determine the overall heat transfer coefficient (based on the inside surface area) in kW/m^2·deg C. A. 1.61 B. 2.55 C. 1.09 D. 7.85 do fast i will 6 upvotes.
do fast
Chart and Regression analysis : What does the intercept predict? X: C16 (number of cars on the sales lot) versus Y: C17 (cars sold per day) Equation: y=2.9x + 14.5 Slope:2.9 Intercept:14.5 Does the intercept mean the intercept is 14.5 means that the cars sold per day( Y) predicted number of cars on sale lot(X) to be 14.5, but this intercept has no meaning. So, I will not use to predict cars sold per day?
do fast
(3) The Elon Company manufactures parts for an aircraft company using three computerized numerical controlled (CNC) turning centers. The company has to decide which machines are capable of producing a specific part with design specifications of 0.0970 inch ± 0.015 inch. The machines have the following parameters: Machine 1 (x= 0.0995, o = 0.004); Machine 2 ( = 0.1002, o = 0.009); Machine 3 (x = 0.095, o = 0.005). Determine which machines (if any) can produce the products within the design specifications. ||

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

SEE MORE TEXTBOOKS

For the figure below, determine the magnitude of the linear velocity of joint C, in m/s: V₁ = 1.5 m/s VA aA = 0.5 m/s² 90° 0.5 m B A 60° 0.6 m