Determine the allowable pile load capacity of the 40 cm diameter driven concrete pile shown in the Figure (1). W.T. Figure (1) K=1 6=0.750 3 m 6 m K = 2 6=0.750 5 m Loose sand Y₁ = 16 kN/m², '= 30° Soft clay Year = 18 kN/m, 2 C= 15 kN/m² Dense sand Ysat = 20 kN/m², -40°

Determine the allowable pile load capacity of the 40 cm diameter driven concrete pile shown in the Figure (1). W.T. Figure (1) K=1 6=0.750 3 m 6 m K = 2 6=0.750 5 m Loose sand Y₁ = 16 kN/m², '= 30° Soft clay Year = 18 kN/m, 2 C= 15 kN/m² Dense sand Ysat = 20 kN/m², -40°

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.21P: Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf...

See similar textbooks

Similar questions

Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5 fill. FIG. 18.26 Negative skin friction
Refer to Figure 18.13. Given L1 = 1.5 m, L2 = 3 m; for the sand, =33, =16.5kN/m3, sat=19.0kN/m3; and, for the clay, c=50kN/m2, =0, sat=20kN/m3. Determine the depth of sheet pile required, allowing for a 50% increase from the theoretical estimate.
In Problem 18.4, find the maximum bending moment in the sheet pile and determine the required section modulus, assuming an allowable stress of 190 MN/m2. 18.4 Refer to Figure 18.13. Given L1 = 1.5 m, L2 = 3 m; for the sand, =33, =16.5kN/m3, sat=19.0kN/m3; and, for the clay, c=50kN/m2, =0, sat=20kN/m3. Determine the depth of sheet pile required, allowing for a 50% increase from the theoretical estimate.
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60 kN/m2. Determine the maximum allowable load (Qall) with FS = 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load. Allow a factor of safety of 3. What percentage of the ultimate load is being carried by the pile shaft? Is it a friction pile?
Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
Redo Problem 12.20 using Vesics method, assuming that the skin friction is distributed uniformly along the shaft. 12.20 A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Refer to Figure 18.9. A cantilever sheet pile is driven into a granular soil where the water table is 2 m (L1) below the top of the sand. The properties of the sand are =40, =17.5kN/m3, and sat=19kN/m3. It is proposed to excavate to a depth of 6 m (L) below the ground level. Determine the actual depth to which the sheet pile must be driven (L + D), using the net lateral pressure diagram. Note: Dactual=1.3(L3+L4)theory
Redo Problem 12.30 assuming that the water table coincides with the top of the fill and that sat(fill) = 19.8 kN/m3. If the other quantities remain the same, what would be the downward drag force on the pile? Assume ' = 0.5fill. 12.30 Figure 12.49a shows a pile. Let L = 15 m, D (pile diameter) 305 mm, Hf = 3 m, fill = 17.5 kN/m3, and fill = 25°. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5fill.
Redo Problem 18.10 using the method for estimating the skin resistance. 18.10 A concrete pile 15 m long with a cross section of 380 mm 380 mm is fully embedded in a saturated clay layer. For the clay, sat = 18 kN/m3, = 0, and cu = 80 kN/m2. Assume that the water table lies below the tip of the pile. Determine the allowable load that the pile can carry (FS = 3). Use the a method to estimate the skin resistance.
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
A steel pile (H-section; HP 360 1.491; see Table 18.1) is driven into a layer of sandstone The length of the pile is 18.9 m. Following are the properties of the sandstone: Unconfined compression strength = qu(lab) = 78.7 MN/m2 Angle of friction = 36 Using a factor of safety of 3, estimate the allowable point load that can be carried by the pile. Use Eq. (18.42).