12.36 Figure P12.36 shows a 3 × 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center- to-center spacing of 1200 mm. Qall = ? Clay Cu= 60 kN/m² Clay Cu= 90 kN/m² 5 m 7 m

12.36 Figure P12.36 shows a 3 × 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center- to-center spacing of 1200 mm. Qall = ? Clay Cu= 60 kN/m² Clay Cu= 90 kN/m² 5 m 7 m

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.36P: Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in...

See similar textbooks

Similar questions

Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
A steel pile (H-section; HP 360 1.491; see Table 18.1) is driven into a layer of sandstone The length of the pile is 18.9 m. Following are the properties of the sandstone: Unconfined compression strength = qu(lab) = 78.7 MN/m2 Angle of friction = 36 Using a factor of safety of 3, estimate the allowable point load that can be carried by the pile. Use Eq. (18.42).
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
A 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Qp by a. Meyerhofs method b. Vesics method c. Coyle and Castellos method Use m = 600 in Eq. (12.28).
Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5 fill. FIG. 18.26 Negative skin friction
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Redo Problem 18.10 using the method for estimating the skin resistance. 18.10 A concrete pile 15 m long with a cross section of 380 mm 380 mm is fully embedded in a saturated clay layer. For the clay, sat = 18 kN/m3, = 0, and cu = 80 kN/m2. Assume that the water table lies below the tip of the pile. Determine the allowable load that the pile can carry (FS = 3). Use the a method to estimate the skin resistance.
Redo Problem 12.20 using Vesics method, assuming that the skin friction is distributed uniformly along the shaft. 12.20 A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
A 400 mm 400 mm square precast concrete pile of 15 m length is driven into a sand where = 18.0 kN/m3 and = 33. Assuming = 0.7 and K = 1.4Ko, determine the load carrying capacity of the pile with factor of safety of 3.0.
Redo Problem 12.3 using Coyle and Castellos methods for estimating both Qp and Qs. 12.3 A 500 mm diameter and 20 m long concrete pile is driven into a sand where = 18.5 kN/m3 and = 32. Assuming = 0.7 and K = 1.5 Ko, determine the load-carrying capacity of the pile, with a factor of safety of 3. Use Meyerhofs method [Eq. (12.18)] for computing the point load-carrying capacity Qp, and Eqs. (12.42) and (12.43) for computing the load-carrying capacity of the pile shaft Qs.
Determine the maximum load that can be allowed on a 450 mm diameter driven pile shown in Figure P12.6, allowing a factor of safety of 3. Use K = 1.5 Ko and = 0.65 in computing the shaft load. Use Meyerhofs method for computing the point load.
Solve Problem 12.23 using the method of Broms. Assume that the pile is flexible and free headed. Let the soil unit weight, = 16 kN/m3; the soil friction angle, = 30; and the yield stress of the pile material. FY = 21 MN/m2. 12.23 A 30 m long concrete pile is 305 mm 305 mm in cross section and is fully embedded in a sand dcposit. If nh = 9200 kN/m2, the moment at ground level Mg = 0, the allowable displacement of pile head = 12 mm; Ep = 21 106 kN/m2, and FY(pile) = 21,000 kN/m2, calculate the allowable lateral load, Qg, at the ground level. Use the elastic solution method.