(d) The yield strength values of pure aluminium (Al) and pure copper (Cu) are 25 MPa and 20 MPa, respectively; whereas the yield strength values of cold rolled Al-Mn-Mg alloy and cast 60-40 Brass (60% Cu, 40% Zn) are 200 MPa and 105 MPa, respectively. With aid of schematics, explain the main mechanisms account for the increases in the strengths. (e) A cylindrical tie rod with a diameter of 18.4 mm is subjected to cyclic loading. The stress range is +/- 200 kN. Figure Q3.3 shows the S-N curve of the material of which the rod is made, how many cycles will this rod survive? Stress amplitude J. (MPa) 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 10² 103 104 4340 low-alloy steel Stress ratio= -1 105 106 Number of cycles to failure, Nf 107 108

(d) The yield strength values of pure aluminium (Al) and pure copper (Cu) are 25 MPa and 20 MPa, respectively; whereas the yield strength values of cold rolled Al-Mn-Mg alloy and cast 60-40 Brass (60% Cu, 40% Zn) are 200 MPa and 105 MPa, respectively. With aid of schematics, explain the main mechanisms account for the increases in the strengths. (e) A cylindrical tie rod with a diameter of 18.4 mm is subjected to cyclic loading. The stress range is +/- 200 kN. Figure Q3.3 shows the S-N curve of the material of which the rod is made, how many cycles will this rod survive? Stress amplitude J. (MPa) 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 10² 103 104 4340 low-alloy steel Stress ratio= -1 105 106 Number of cycles to failure, Nf 107 108

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Discuss the variations in nature of the stress-strain graphs of steel and aluminium.
A ductile cast-iron bar is to support a load of 178 kN in a heat-treating furnace used to make malleable cast iron. The bar is located in a spot that is continuously exposed to 500°C. Design the bar so that it can operate for at least 10 years without failing.
hand written otherwise skip
sketch
Describe the final microstructure obtained in a 1050 steel after heat at 8200C, cooled to 7000C and hold for 5 s, cooled to room temperature. 900- a+y 800 A, 700 A1 F, Pr a+ pearlite 23 600 -y+a+pearlite 30 500 B1 y+ bainite Bainite 39 F=Ferrite B, M, 400 49 P=Pearlite 300 Y+ martensite B=Bainite 200 Martensite M=Martensite 62 100- 102 10 10 10 10 0.1 1 10 Time (s) TTT curve for carbon steel AISI 1050 Temperature (°C) Rockwell C hardness
The lower yield point for a certain plain carbon steel bar is found to be 135 MPa, while a second bar of the same composition yields at 260 MPa. Metallographic analysis shows that the average grain diameter is 50 µm in the first bar and 8 µm in the second bar. Predict the grain diameter needed to cause a lower yield point of 205 MPa.
A sheet of a 70% Cu-30% Zn alloy is cold-rolled 20% to a thickness of 3.0mm. The sheet is then further coldrolledto 2.0 mm. What is the percentage cold work?
(ii) The turbine blade root is found to contain a surface fatigue crack of 3.3 mm during a routine maintenance inspection. The major stop-start load cycle is experienced twice per day with a minimum stress of 34 MPa and a maximum stress of 195 MPa. The turbine blade has a KIC of 75 MPa√m. Fatigue crack growth rate data for this alloy is given by: the Paris law constant, A = 4.5 x 10-11 and the Paris law exponent, m = 3.8. How many more stop-starts would you recommend be used? Explain your reasoning. You can assume the shape factor Q = 1.2, K is in MPaNm and a (crack length) is in m
(2) Consider a homogeneous structure made out of metal subjected to homogeneous boundary conditions t = σn. For o corresponding to uniaxial, biaxial and shear stress state, calculate the stress at which the material yields.
A hypothetical metal alloy has a grain diameter of 2.4 × 10-2 mm. After a heat treatment at 575°C for 500 min, the grain diameter has increased to 5.6 × 10-2 mm. Compute the time required for a specimen of this same material (i.e., do = 2.4 × 10-² mm) to achieve a grain diameter of 5.5 x 10-2 mm while being heated at 575°C. Assume the n grain diameter exponent has a value of 2.2. i min
Please solve
13.8 - Howson et al.studied the creep and stress-rupture response of oxidedispersion-strengthened (ODS) superalloys produced by mechanical alloying. They determined that the activation energy for creep Qc was 619 kJ/mol by conducting tests at a constant applied stress of 558.7 MPa at the three temperatures of 746, 760, and 774 °C. (a) The results shown in Figure Ex13.8 were found for experimental alloy MA6000 E at 760 °C. Estimate the value of n, and discuss this value in terms of the microstructure exhibited by the alloy (made by means of dispersion-strengthening by inert yttrium oxide dispersoids plus precipitation-strengthening by gamma prime). (b) By applying Equation 13.4, show how the activation energy can be found. Make the appropriate plot, and find the minimum creep rate at the aforementioned three temperatures. Note that the activation energy is given per mole. 1) Where in the book/slides is this covered? = page # or slide session/number 2) What equations and concepts apply…