Steady-state creep data taken for an iron at a stress level of 136 MPa are given here: If it is known that the value of the stress exponent n for this alloy is 8.3, compute the steady-state creep rate at 1300 K and a stress level of 83 MPa. i és (h-¹) T(K) 6.7 x 10-4 1100 8.5 x 10-2 1200 h-1

Steady-state creep data taken for an iron at a stress level of 136 MPa are given here: If it is known that the value of the stress exponent n for this alloy is 8.3, compute the steady-state creep rate at 1300 K and a stress level of 83 MPa. i és (h-¹) T(K) 6.7 x 10-4 1100 8.5 x 10-2 1200 h-1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Match the image with the material property depicted by the image. - 1.…

A: Ductile failure or fracture: When the tensile stress increase in a ductile material than it behaves…

Q: A cold worked Al-alloy component takes 200 minutes to recrytallize at 250 °Č but takes 14 minutes at…

A: Solution: Given Data: t1=200 minutesT1=250oCt2=14 minutesT2=276oCT3=320oC…

Q: Iculate the activation energy (in J/mol) for creep for an alloy having the steady state creep havior…

Q: Temperature (°C) 1600 (1) 1400 1200 1000 800 600 400 1538°C (Fe) 912°C 8+7 1394°C(F) -1493°C (G) y,…

A: Given:

Q: The yield region for steel that has a normal grain diameter of 2.4x10-2 mm is 260 MPa. At a grain…

Q: Steady-state creep rate data are given here for some alloy taken at 200°C (473 K): i Es (h-¹) 2.2 x…

Q: Question The yield strength for an aluminum alloy that has an average grain diameter of 10 um is 400…

A: OPTION B -668MPa is the right answer. Detailed explanation and solution of the above problem…

Q: 1900 Fo = Forsterite 1800 Liquid En = Enstatite Qz = Quartz 1700 Fo+liq 1600 -En+lig Qz+liq 1500…

A: From the olivine mineral group, forsterite is a magnesium silicate crystal with the chemical formula…

Q: The fatigue life of a certain steel was found to be 10* cycles at + 70 MPa and 10 cycles at + 50…

Q: (6) For an aluminum alloy under constant load, the creep rate increased by a factor of 2 when the…

Q: Which of the following startements is incomeef? A Under and fatigne 1oa0ding materials may fail at…

A: The incorrect statement out of the above given statements is option (D) (D) Choosing the material…

Q: Do provide explanations too. Thank you.

A: The grain boundary and bulk diffusion creep both are the mechanism that leads to the elongation of…

Q: 8- For the S-N plot below, determine the following: a. What is the fatigue limit for this alloy? b.…

A: Given: The stress amplitude is σa1=400 MPa and σa2=255 MPa. Concept used: Fatigue limit: The number…

Q: The yield strength for an alloy that has an average grain diameter of 1.6 × 10² mm is 320 MPa. At a…

Q: For the alloy Mg-45 wt % Pb alloy at 500°C, what is the weight percentage of Pb in Liquid? It does…

A: Given: The wt percentage of Pb, Co = 45 The temperature of alloy, T = 500 C

Q: Calculate the activation energy in j/mol for the creep of an alloy having the steady state creep…

Q: 2. Immediately after recrystallization during annealing, this alloy was quickly cooled. Assume that…

A: Based on the information provided, the likely mechanism for the increase in yield strength (σy)…

Q: Using Figure 4-1 (ductility (%El) - percent cold work), determine the change in cross section of a…

Q: Determine the structural constitution of a steel with 0.4% carbon at 727ºC during its cooling.…

A: The iron-carbon phase diagram is a graphical representation of the phase behavior of an iron-carbon…

Q: Steady-state creep rate data are given here for some alloy taken at 200°C (473 K): i, (h) a (MPa)…

A: Find the steady state creep rate .

Q: You need to produce a Ci-Ni alloy having minimum yield strength of 20,000psi, a minimum tensile…

A: Required properties for Cu-Ni alloy:Minimum yield strength (σy) = 20,000 psiMinimum tensile strength…

Q: | 1. A stacking fault region is a planar defect TT 2. Screw dislocation can cross slip under…

Q: These questions are based on a high carbon stell with a composition of 1.5%C and 98.5%Fe 1)Name the…

A: Given 1.5 wt% C and 98.5 wt%Fe so Co=1.5 wt%C

Q: 11. Steady-state creep rate data are given below iron at 900 C. &($) 104 10-6 σ (MPa) 17 6.5 If it…

Q: Consider 1.0 kg of a 99.4 wt% Fe-0.6 wt% C alloy that is cooled to a temperature just below the…

Q: If you could produce AISI 1020 steel with a grain size of 50 nm, what would be the expected yield…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Steady-state creep data taken for an iron at a stress level of 136 MPa are given here:
If it is known that the value of the stress exponent n for this alloy is 8.3, compute the steady-state creep rate at 1300 K and a stress
level of 83 MPa.
i
Es (h-¹)
T(K)
6.7 x 104
1100
8.5 x 10-2 1200
h-1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the tensile stress-strain diagram in the figure below labeled 1 and 2.
The flow stress of a coarse-grained dilute copper alloy increased from 2 to 55 MPa when the dislocation density was increased from a low value of 10 cm via cold working to a modest value of 100 cm2. Calculate the flow stress for this alloy when heavy cold working introduces a dislocation density of 10¹2 cm². An equation similar to the Hall-Petch equation has been proposed for dislocations, and is: Tflow To ka Paisl where Tflow is the flow stress (i.e., the force per unit area necessary to get plastic deformation), pdisi is the dislocation density (the dislocation line length per unit volume), and To and ka are constants for a given material. The easiest way to solve this problem is to put values into this equation twice, subtract one expression from the other, and solve for ka. Then enter your value of ka into either original equation to determine To. Keep track of units, and then solve the problem stated above.
q11
N MPa = 10 2.2. When the Hall-Petch coefficient is 20 GPa nm/2, estimate the grain size of this alloy after recrystallization. -1/2 d O=O₂+ Kuda куба го вра има че app MPa = 150 MPa + 20 × 10 °MPant -150MPa 1
Ductility (%EL) 70 60 50 40 30 20 10 Brass 1040 Steel 10 Copper 20 30 40 50 Percent cold work 60 70 Percent cold work = 0 Ductility = 0
Help me please
Identify the main properties trend (grain size, ductility, strength, hardness) of metal alloys as a percent of cold work on the diagram below.
The properties of a titanium allow used in commercial airplanes are shown in the table: Strength (MPa) Grain Size (mm) 0.020 162 0.055 148 Determine a) the constants of the Hall-Petch equation and b) the grain size required to obtain a strength of 192 MPa
i need the answer quickly
The engineering yield strength of an alloy is 80 ksi.
the behaviour of graphite materials under stress
The yield strength for an alloy that has an average grain diameter of 5.9 x 10-2 mm is 148 MPa. At a grain diameter of 7.8 × 10-³ mm, the yield strength increases to 233 MPa. At what grain diameter, in mm, will the yield strength be 247 MPa? d = i mm