QuestionThe yield strength for an aluminum alloy that has an average grain diameter of 10 umis 400 MPa. As the grain diameter is increased to 80 um, the yield strengthdecreases to 260 MPa. When the grain diameter is 2 um, its yield strength is close to760 MPa668 MPa566 MPa419 MPa

OPTION B -668MPa is the right answer. Detailed explanation and solution of the above problem…

Question The yield strength for an aluminum alloy that has an average grain diameter of 10 um is 400 MPa. As the grain diameter is increased to 80 μm, the yield strength decreases to 260 MPa. When the grain diameter is 2 um, its yield strength is close to 760 MPa O668 MPa 566 MPa 419 MPa

Question The yield strength for an aluminum alloy that has an average grain diameter of 10 um is 400 MPa. As the grain diameter is increased to 80 μm, the yield strength decreases to 260 MPa. When the grain diameter is 2 um, its yield strength is close to 760 MPa O668 MPa 566 MPa 419 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hypothetical metal alloy has a grain diameter of 2.4 × 10-2 mm. After a heat treatment at 575°C for 500 min, the grain diameter has increased to 5.6 × 10-2 mm. Compute the time required for a specimen of this same material (i.e., do = 2.4 × 10-² mm) to achieve a grain diameter of 5.5 x 10-2 mm while being heated at 575°C. Assume the n grain diameter exponent has a value of 2.2. i min
Help me please
A metallic tube has an outer diameter of 500 mm and a wall thickness of 30 mm (Figure 4). The working internal pressure of the tube is 15 MPa and the fracture toughness of the material (K₁c) ranges from 40 MN/m³/2 to 50 MN/m³/2. Select a value for Kic and determine the size of the largest flaw the tube can contain. Assume that for this geometry K σφπα. = 30 mm! 500 mm Figure surface flaws 4 (not to scale)
The flow stress for an alloy is 115 Mpa when its dislocation density is 10^6 cm^-2 and 207 Mpa when its dislocation density is 10^8 cm^-2. When the flow stress is 359 Mpa, Find the dislocation density.
The properties of a titanium allow used in commercial airplanes are shown in the table: Strength (MPa) Grain Size (mm) 0.020 162 0.055 148 Determine a) the constants of the Hall-Petch equation and b) the grain size required to obtain a strength of 192 MPa
The minimum yield strength for iron with an average grain size of 6x10-²mm is 135 MPa, this increases to 260 MPa when the average grain size is reduced to 8x10-³ mm. What must the average grain size be to achieve a yield strength of 205 MPa.
Consider a dislocation condition as shown below. A) what is the strain state in the upper region and B) how would addition of small impurity atoms in the region indicated by "*"s change it? oooooo OOOOO DO Select one: a. Compressive, would reduce compressive strain O b. Tensile, would decrease tensile strain O C. Compressive, would increase compressive strain Od. Tensile, would increase tensile strain Oe. Shear, would increase compressive strain
What is a solid solution? In general, what is its implication on the mechanical behavior of metals (i.e., increase or decrease in strength)?
Material science question
an alloy with an avg grain diameter of 0.053 mm is l16 MPa. When the grain diameter is 0.008Amm, the yeild strength goesupto 231 MPa.lf the yeild strength is 207MPA, what would the grain diameter be?
Consider a single crystal of a hypothetical metal that has the BCC crystal structure. A stress of 50 MPa is applied in the [101] direction of the BCC unit cell.a. Determine the most favourable slip direction for the (011) slip plane of the BCC unit cell. ⟨111⟩ is the family of directions with the highest linear density in the BCC unit cell.b. If τcrss = 27.5 MPa, determine if the single crystal yields. If not, what stress level is required?c. What is the minimum stress at which the BCC single crystal yields?
The yield point for a brass alloy that has an average grain diameter of 50 micrometers is 120 MPa.