The yield point for a brass alloy that has an average grain diameter of 50 micrometers is 120 MPa. The yield point for a brass alloy that has an average grain diameter of 50 µm is 120 MPa. At a grain diameter of 10 µm, the yield point increases to 240 MPa. At whatgrain diameter (in µm) will the yield point be 200 MPa?

Answered: Image /qna-images/answer/e345d70c-14c4-4ba2-9be0-c11bfd9d2632.jpg

The yield point for a brass alloy that has an average grain diameter of 50 um is 120 MPa. At a grain diameter of 10 um, the yield point increases to 240 MPa. At what grain diameter (in um) will the yield point be 200 MPa?

The yield point for a brass alloy that has an average grain diameter of 50 um is 120 MPa. At a grain diameter of 10 um, the yield point increases to 240 MPa. At what grain diameter (in um) will the yield point be 200 MPa?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Do not answer in image format
How does strain hardening and grain size reduction affect elastic modulus
4. The mechanical properties of a given titanium alloy (Ti-6Al-4V) are E = 114 GPa, σy = 880 MPa and Kic = 75 MPa√m. What is the approximate plastic zone size? How large must a part be made if we want to test its K₁ using LEFM?
The minimum yield strength for iron with an average grain size of 6x10^-2 mm is 135 MPa, this increases to 260 MPa when the average grain size is reduced to 8x10^-3 mm.What must the average grain size be to achieve a yield strength of 205 MPa.
A single crystal of aluminum is oriented for a tensile test such that its slip plane normal makes an angle of 28.1° with the tensile axis. Three possible slip directions make angles of 62.4°, 72.0°, and 81.1° with the same tensile axis. (a) Which of these three slip directions is most favored? (b) If plastic deformation begins at a tensile stress of 1.95 MPa (280 psi), determine the critical resolved shear stress for aluminum.
The diagram below shows a microscopic metal rod with a single crystal structure whose orientation is indicated by the inset. A force of F = 15.7 N is applied to the rod. The cross-sectional area is 1.3 mm2. Calculate the shear stress along the close-packed direction.
You are given three metal test samples, with the same chemical composition and differing grain sizes: A: 5.0, B: 10.0 and C: 20.0 microns. Samples A and B have been tested and have yield stresses of 142.4 MPa and 135.8 MPa (all numbers are rounded off to the 1st decimal point). Based on this information, which of the following values do you think will be the closest to the yield stress of Sample C? In calculating the answer, use the Hall-Petch relation between yield stress of a metal o vield and the grain size of the metal d, which is Oyield = 00 + kd¬1/2 where k and og are constants. (This question has only one correct answer) а. 100.6 MPa b. 131.1 MPa С. 152.4 MPa O d. 115.8 MPa е. 128.1 MPa
The lower yield point for a certain plain carbon steel bar is found to be 135 MPa, while a second bar of the same composition yields at 260 MPa. Metallographic analysis shows that the average grain diameter is 50 µm in the first bar and 8 µm in the second bar. Predict the grain diameter needed to cause a lower yield point of 205 MPa.
N MPa = 10 2.2. When the Hall-Petch coefficient is 20 GPa nm/2, estimate the grain size of this alloy after recrystallization. -1/2 d O=O₂+ Kuda куба го вра има че app MPa = 150 MPa + 20 × 10 °MPant -150MPa 1
5. Consider a single crystal of some hypothetical metal that has the FCC crystal structure and is oriented such that a tensile stress is applied along a [102] direction. If slip occurs on a (111) plane and in a [101] direction, compute the stress at which the crystal yields if its critical resolved shear stress is 3.42 MPa.
Pls do this question at any cost
A hypothetical metal alloy has a grain diameter of 2.4 × 10-2 mm. After a heat treatment at 575°C for 500 min, the grain diameter has increased to 5.6 × 10-2 mm. Compute the time required for a specimen of this same material (i.e., do = 2.4 × 10-² mm) to achieve a grain diameter of 5.5 x 10-2 mm while being heated at 575°C. Assume the n grain diameter exponent has a value of 2.2. i min