13.8 - Howson et al.studied the creep and stress-rupture response of oxidedispersion-strengthened (ODS) superalloys produced by mechanical alloying. They determined that the activation energy for creep Qc was 619 kJ/mol by conducting tests at a constant applied stress of 558.7 MPa at the three temperatures of 746, 760, and 774 °C. (a) The results shown in Figure Ex13.8 were found for experimental alloy MA6000 E at 760 °C. Estimate the value of n, and discuss this value in terms of the microstructure exhibited by the alloy (made by means of dispersion-strengthening by inert yttrium oxide dispersoids plus precipitation-strengthening by gamma prime). (b) By applying Equation 13.4, show how the activation energy can be found. Make the appropriate plot, and find the minimum creep rate at the aforementioned three temperatures. Note that the activation energy is given per mole. 1) Where in the book/slides is this covered? = page # or slide session/number 2) What equations and concepts apply here? Strain, 5 1 20 586 MPa 40 60 80 Time, h 538 MPa 100 120 145 Ess = AGb kT ADGb b KT d р -Do exp(-Qc/RT) n G'))" Precision with logs, exponentials, etc.

13.8 - Howson et al.studied the creep and stress-rupture response of oxidedispersion-strengthened (ODS) superalloys produced by mechanical alloying. They determined that the activation energy for creep Qc was 619 kJ/mol by conducting tests at a constant applied stress of 558.7 MPa at the three temperatures of 746, 760, and 774 °C. (a) The results shown in Figure Ex13.8 were found for experimental alloy MA6000 E at 760 °C. Estimate the value of n, and discuss this value in terms of the microstructure exhibited by the alloy (made by means of dispersion-strengthening by inert yttrium oxide dispersoids plus precipitation-strengthening by gamma prime). (b) By applying Equation 13.4, show how the activation energy can be found. Make the appropriate plot, and find the minimum creep rate at the aforementioned three temperatures. Note that the activation energy is given per mole. 1) Where in the book/slides is this covered? = page # or slide session/number 2) What equations and concepts apply here? Strain, 5 1 20 586 MPa 40 60 80 Time, h 538 MPa 100 120 145 Ess = AGb kT ADGb b KT d р -Do exp(-Qc/RT) n G'))" Precision with logs, exponentials, etc.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A material is required as heating elements for an electrical resistance furnace for heat treating steels. Make and list appropriate assumptions for temperature and furnace environment. List what you would judge to be the design-limiting properties. Name three candidate heating element materials.
Excellent combinations of hardness, strength, and toughness are obtained from bainite. One heat treater austenitized a eutectoid steel at 750°C, quenched and held the steel at 250°C for 15 min, and finally permitted the steel to cool to room temperature. Did he produce the required bainitic structure? Use the diagram below in your answer 900 600 700 14 00 Y. 400 12 52 M. 00 57 M. 100 0.3 10 10 10 Answer: Time Temperature ("C) Rockwell Chardnens
Based on the IT diagram for an iron-carbon alloy of eutectoid composition, specify the final microstructure (in terms of microconstituents present and percentages of each) of a specimen subjected to the following time-temperature treatments Cool rapidly to 650oC, hold for 104s then quench Reheat the specimen in (a) to 700oC for 20h Cool rapidly to 400oC hold for 2s then quench to room temp Cool rapidly to 400oC hold for 20s then quench to room temp Cool rapidly to 575oC hold for 20s, cool rapidly to 350oC hold for 100s then quench to room temp.
(a) Briefly describe at least five methods to increase the strength of materials. (b) What are the metallurgical/processing techniques employed to enhance the creep resistance of metal alloys? (c) Cite three variables that determine the microstructure of an alloy. (d) What are the most common types of crystal defects and how do they affect properties? (e) Briefly describe the phenomenon of coring and why it occurs.
Write a short representation of an automaton steel with 0.20% C, 0.28% S, 1.1% Mn and 0.2% Pb in its composition according to Turkish Standards.
Using the isothermal transformation diagram for a 0.45 wt% C steel alloy (Animated Figure 10.40), determine the approximate percentages of the microconstituents that form the final microstructure of a small specimen that has been subjected to the following time- temperature treatments. In each case assume that the specimen begins at 845°C (1550°F), and that it has been held at this temperature long enough to have achieved a complete and homogeneous austenitic structure.
The flow stress of a coarse-grained dilute copper alloy increased from 2 to 55 MPa when the dislocation density was increased from a low value of 10 cm via cold working to a modest value of 100 cm2. Calculate the flow stress for this alloy when heavy cold working introduces a dislocation density of 10¹2 cm². An equation similar to the Hall-Petch equation has been proposed for dislocations, and is: Tflow To ka Paisl where Tflow is the flow stress (i.e., the force per unit area necessary to get plastic deformation), pdisi is the dislocation density (the dislocation line length per unit volume), and To and ka are constants for a given material. The easiest way to solve this problem is to put values into this equation twice, subtract one expression from the other, and solve for ka. Then enter your value of ka into either original equation to determine To. Keep track of units, and then solve the problem stated above.
please draw each question on the TTT diagram
The minimum yield strength for iron with an average grain size of 6x10^-2 mm is 135 MPa, this increases to 260 MPa when the average grain size is reduced to 8x10^-3 mm.What must the average grain size be to achieve a yield strength of 205 MPa.
Discuss under what circumstances martensite is formed and highlight its effect on mechanical properties.
3 Materials Science. From picture below.Describe in detail the phase transformations (showing cooling curves, corresponding optical backgrounds, etc.) that takes place during solidification of the following alloys:(a) 99% Cu - 1% Al(b) 96% Cu - 4% Al(c) 80% Cu - 20% Al
Use molar masses to demonstrate that Fe3C (cementite, iron carbide) corresponds to 6.7 wt% C.