please use 3 decimals in your calculations and 2 in your answer Calculate the voltage across R4 (VR4) in the following circuit, when the values for resistors and sources are:R1= 50 OhmsR2= 56 OhmsR3=40 OhmsR4=31 OhmsV1= 7 Volts11=4 AmperesR3R1wwR2V1wwww11R4VR4Give your answer in Volts (not milli Volts, or kilo Volts)

Step 1: Step 2: Step 3: Step 4:

Answered: Calculate the voltage across R4 (VR4)…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

in the circuit, the voltage across R1 in volts is ___ in the circuit, the voltage across R2 in volts is ___ in the circuit, the voltage across R3 in volts is ___
Please help me solve for the total resistance, and total current if:Vt = 20 VR1 = 2 ohmsR2 = 5 ohmsR3 = 7 ohmsR4 = 8 ohmsR5 = 3 ohmsR6 = 4 ohmsR7 = 9 ohmsR8 = 6 ohmsR9 = 10 ohmsR10 = 7 ohms
Q6
R1 of 90 kilo ohm and R2 of 10 kilo ohm are in series across a 43-volt source. A) Draw the schematic diagram. B) What is the voltage drop at R2?
Nichrome ribbon resistor elements each has a resistance of 1 ohm. The element is made from sheet of nichrome alloy, 0.025 cm thick. If the width of the ribbon is 0.3 cm, what length is required per element? [centimeters, 1 decimal place]
3. The figure on the left below shows a schematic diagram of a battery. The voltage measured by U1 is called the terminal voltage given R1 = 1 ohm. In the figure on the right below, the terminal voltage of each of the battery-resistor combination is Vr = 1.5 volts. Find the following: a. The current passing through R5. b. The currents passing through R1 and R3 C. The voltage across R1. d. The voltage of the battery EMF. e. The percentage of voltage loss ot the battery due to the internal resistance R1. The power dissipated by the internal resistance R1. g. The power dissipated by R5 if R1 = R2 = R3 = R4 = 0. h. The percentage of power dissipation loss due to the four resistors R1, R2, R3, and R4 f. R1 R3 S10 R1 U1 1.500 EMF EMF R5 100 V1 R2 $10 EMF R4 EMF EMF
1
If PMMC meter have internal resistance of 1002 and full-scale range of 1mA. Assume we wish to increase the meter range to 2A. the value of shunt resistor will be: OR_sh=0.00500 OR_sh= 0.00010 OR_sh=0.11111 0
(01) Zener Diode Circuits. (Course: Electronic Devices and Circuit Theory) -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
Asap plzzx
We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SLIDE SWITCH: LEFT- OFF MIDDLE- DC VVOLTS DC mA NUMERICAL VALUE OF VOLTS OR MA OR OHMS DISPLAYED HERE 0.00 OHMS FIGHT - AC VOLTS AC mA OFFOO AC DC-n DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS (SELECT RANGE) 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 20 200 2K 20K. 200 200K 2M 20M MOVE ROTARY SWITCH TO THIS AREA TO READ mA (SELECT RANGE) *20u 200u 200m 20m 10A mA COM PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin NOT CONNECTED
The current enters to the positive terminal of a device is i(t) = e-4t amps, and the voltage across the device is v(t) = 3 d(i)/dt volt. The amount of energy absorbed (in Joule) in between t = 0 and t = 2 seconds is in the range of (e-16 1.125 x 10-7) (a) - 5.89 to - 5.90 (c) - 4.711 to -4.713 (b) - 5.99 to -6.00 (d) -1.49 to -1.51

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Calculate the voltage across R4 (VR4) in the following circuit, when the values for resistors and sources are: R1= 50 Ohms R2= 56 Ohms R3=40 Ohms R4=31 Ohms V1= 7 Volts 11=4 Amperes R3 R1 ww R2 V1 ww ww 11 R4VR4 Give your answer in Volts (not milli Volts, or kilo Volts)